Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2017.06
RM2170E _58 Vehicle Interior _057044 INTERIOR PANELS / TRIM _0278146 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


PROCEDURE

Hide 1.INSTALL ROOF HEADLINING ASSEMBLY

a.
B301725

Pull the roof headlining back into the vehicle through the back door.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.



b.

Engage the 2 claws.


c.

Install the roof headlining assembly with the 3 clips.


d.

for front pillar RH side:

i.

Engage the 3 clamps.


ii.

Connect the connector.



e.

for front pillar LH side:

i.

Engage the 3 clamps.


ii.

Connect the connector.



f.

for rear pillar RH side:

i.

Engage the 2 clamps.


ii.

Connect the connector bracket with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


iii.

Connect the connector.



Hide 74348 2.INSTALL VISOR HOLDER

a.
B211698

Engage the 2 claws and turn the visor holder 45° counterclockwise to install it.

HINT:

Use the same procedure for the RH side and LH side.



Hide 74320 3.INSTALL VISOR ASSEMBLY LH

a.
B322943

Install the visor assembly LH with the 2 screws.

HINT:

Install the visor assembly LH with the arrow facing the front of the vehicle.



b.

Connect the visor shaft into the visor holder.


Hide 74310 4.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74631C 5.INSTALL COAT HOOK (w/ Coat Hook)

HINT:

Use the same procedure to install all coat hooks.


a.
B302261

Assemble the coat hook as shown in the illustration.


b.
B302262

Install the coat hook.


Hide 74610S 6.INSTALL ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure to install all assist grips.


a.
B203057

Assemble the front assist grip assembly as shown in the illustration.


b.
B229265

Install the assist grip assembly.


Hide 81240 7.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/ Room Light)

Hide 81260A 8.INSTALL MAP LIGHT ASSEMBLY

Hide 62472A 9.INSTALL ROOF SIDE INNER GARNISH LH

a.

Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH.


b.

Engage the 5 clips to install the roof side inner garnish LH.


Hide 73350 10.CONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY

Hide 64740C 11.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Engage the guide, 4 claws and 4 clips.

B300800E03
2.104,3.948 2.344,4.021 false 1.948,3.875 2.135,4.042 0.188,0.167 10 true *a

Text in Illustration
*a Rear Seatback Hinge - -


b.

Install the deck trim side panel assembly LH with the bolt and 2 screws.


c.

Turn the rear seatback hinge as shown in the illustration.


Hide 58732C 12.INSTALL REAR ABSORBER CAP LH

a.

Engage the 2 guides and 2 claws to install the rear absorber cap LH.


Hide 73370 13.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

Hide 62471A 14.INSTALL ROOF SIDE INNER GARNISH RH

a.

Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH.


b.

Engage the 5 clips to install the roof side inner garnish RH.


c.
B297734

Engage the guide and 4 claws to connect the belt guide.


Hide 64730B 15.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 81330 16.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 58731C 17.INSTALL REAR ABSORBER CAP RH

HINT:

Use the same procedure as for the LH side.


Hide 73360 18.INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64716D 19.INSTALL REAR DECK TRIM COVER (w/ Coat Hook)

a.

Engage the 2 guides and 4 claws.


b.

Install the rear deck trim cover with the 2 clips.


Hide 64716D 20.INSTALL REAR DECK TRIM COVER (w/o Coat Hook)

a.

Engage the 4 guides and 4 claws.


b.

Install the rear deck trim cover with the 2 clips.


Hide 64330D 21.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

a.

Install the package tray trim panel assembly.


Hide 64777J 22.INSTALL SPARE WHEEL CUSHION (w/ Coat Hook)

a.

Install the 2 spare wheel cushions.


Hide 58570A 23.INSTALL REAR FLOOR MAT ASSEMBLY (w/ Coat Hook)

a.

Install the rear floor mat assembly.


Hide 64997 24.INSTALL DECK FLOOR BOX LH (w/o Coat Hook)

a.

Install the deck floor box LH.


Hide 64995 25.INSTALL DECK FLOOR BOX RH (w/o Coat Hook)

HINT:

Use the same procedure as for the LH side.


Hide 58410B 26.INSTALL DECK BOARD ASSEMBLY (w/o Coat Hook)

a.

Install the deck board assembly.


Hide 62412B 27.INSTALL CENTER PILLAR UPPER GARNISH LH

a.

Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.


b.

Engage the clip.


c.

Install the center pillar upper garnish LH with the 2 screws.


Hide 62414A 28.INSTALL CENTER PILLAR LOWER GARNISH LH

a.

Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.


Hide 73220 29.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73233C 30.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 62332A 31.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B299875E02
2.521,1.104 2.469,0.823 false 1.375,0.656 1.083,0.75 false 2.448,1.115 2.604,1.26 0.156,0.146 10 false *b 1.375,0.573 1.531,0.719 0.156,0.146 10 false *a

Align the alignment mark (White) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

Text in Illustration
*a Alignment Mark (White)
*b Flange Position

NOTICE:

After installation, check that the corners fit correctly.



Hide 62212 32.INSTALL FRONT PILLAR GARNISH LH

a.

Remove the protective cover.


b.
B468935C01
1.875,0.635 2.25,0.635 false 2.177,1.177 2.552,1.177 false 2.281,0.542 2.594,0.698 0.313,0.156 10 false *1 2.583,1.083 2.896,1.24 0.313,0.156 10 false *2
*1 Front Pillar Garnish Clip
*2 Front Pillar Garnish LH


Engage the front pillar garnish clip to the front pillar garnish LH.

HINT:

Make sure that the front pillar garnish clip is engaged correctly.



c.
B482715

Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.


d.
B482714C01
2.104,1.99 2.198,1.813 true 2.021,2 2.333,2.156 0.313,0.156 10 false *1
*1 Front Pillar Garnish Clip


Engage the clip and front pillar garnish clip to install the front pillar garnish LH as shown in the illustration.

HINT:

Make sure that the curtain shield airbag assembly LH is not pinched.



Hide 62312B 33.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B299871E02
2.521,1.135 2.469,0.844 false 1.375,0.688 1.083,0.771 false 2.479,1.167 2.688,1.365 0.208,0.198 10 false *b 1.427,0.583 1.677,0.76 0.25,0.177 10 false *a

Align the alignment mark (Yellow) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

Text in Illustration
*a Alignment Mark (Yellow)
*b Flange Position

NOTICE:

After installation, check that the corners fit correctly.



Hide 62112 34.INSTALL COWL SIDE TRIM BOARD LH

a.

Engage the clip.


b.

Install the cowl side trim board with the clip.


Hide 67914 35.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Engage the 8 claws to install the front door scuff plate.


Hide 67918A 36.INSTALL REAR DOOR SCUFF PLATE LH

a.

Engage the guide and the 5 claws to install the rear door scuff plate.


Hide 62411B 37.INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 38.INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73210 39.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 40.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 62331A 41.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.
B299873E02
2.521,1.104 2.469,0.823 false 1.365,0.656 1.073,0.75 false 2.479,1.146 2.719,1.323 0.24,0.177 10 false *b 1.396,0.542 1.729,0.792 0.333,0.25 10 false *a

Align the alignment mark (Red) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

Text in Illustration
*a Alignment Mark (Red)
*b Flange Position

NOTICE:

After installation, check that the corners fit correctly.



Hide 62211 42.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 43.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B299869E02
2.521,1.208 2.469,0.917 false 1.375,0.76 1.083,0.844 false 2.448,1.208 2.604,1.354 0.156,0.146 10 false *b 1.375,0.677 1.531,0.823 0.156,0.146 10 false *a

Align the alignment mark (Yellow green) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

Text in Illustration
*a Alignment Mark (Yellow green)
*b Flange Position

NOTICE:

After installation, check that the corners fit correctly.



Hide 62111C 44.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 67913 45.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 46.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.