Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › from 2017.06
RM2170E _59 Vehicle Exterior _057046 DOOR / HATCH _0278162 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B227910E03
2.455,0.249 2.625,0.412 0.170,0.163 10 *2 0.711,0.249 0.880,0.412 0.170,0.163 10 *1

Text in Illustration
*1 Centering Bolt
*2 Standard Bolt

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT BACK DOOR

a.

Check that the clearance measurements of areas "a" through "g" are within each standard range.

B301509E02
0.623,2.047 0.831,2.252 0.208,0.205 10 a 1.101,2.419 1.309,2.624 0.208,0.205 10 b 1.993,2.003 2.200,2.208 0.208,0.205 10 c 2.429,2.361 2.637,2.566 0.208,0.205 10 d 5.701,2.272 5.909,2.476 0.208,0.205 10 e 6.274,4.042 6.482,4.247 0.208,0.205 10 f 4.272,5.402 4.480,5.607 0.208,0.205 10 g

Standard Clearance
Area Measurement Area Measurement
a 5.7 to 8.7 mm (0.244 to 0.343 in.) b -0.5 to 2.5 mm (-0.0197 to 0.0197 in.)
c 5.7 to 8.7 mm (0.244 to 0.343 in.) d -0.5 to 2.5 mm (-0.0197 to 0.0197 in.)
e
(Reference)
5.35 mm (0.211 in.) f 3.05 to 7.05 mm (0.12 to 0.278 in.)
g 4.15 to 8.15 mm (0.163 to 0.321 in.) - -


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (w/o Coat Hook)

Hide 64997 3.REMOVE DECK FLOOR BOX LH (w/o Coat Hook)

Hide 64995 4.REMOVE DECK FLOOR BOX RH (w/o Coat Hook)

HINT:

Use the same procedure as for the LH side.


Hide 58570A 5.REMOVE REAR FLOOR MAT ASSEMBLY (w/ Coat Hook)

Hide 64777J 6.REMOVE SPARE WHEEL CUSHION (w/ Coat Hook)

Hide 64330D 7.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 64716D 8.REMOVE REAR DECK TRIM COVER (w/o Coat Hook)

Hide 64716D 9.REMOVE REAR DECK TRIM COVER (w/ Coat Hook)

Hide 10.ADJUST BACK DOOR

a.
B300318

Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.


b.

Tighten the body side hinge after adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
B300319

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


d.

Using a brass bar and a hammer, hit the striker to adjust its position.


e.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 64716D 11.INSTALL REAR DECK TRIM COVER (w/ Coat Hook)

Hide 64716D 12.INSTALL REAR DECK TRIM COVER (w/o Coat Hook)

Hide 64330D 13.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 64777J 14.INSTALL SPARE WHEEL CUSHION (w/ Coat Hook)

Hide 58570A 15.INSTALL REAR FLOOR MAT ASSEMBLY (w/ Coat Hook)

Hide 64997 16.INSTALL DECK FLOOR BOX LH (w/o Coat Hook)

Hide 64995 17.INSTALL DECK FLOOR BOX RH (w/o Coat Hook)

HINT:

Use the same procedure as for the LH side.


Hide 58410B 18.INSTALL DECK BOARD ASSEMBLY (w/o Coat Hook)