1.REMOVE REAR SEAT ASSEMBLY
67918A
2.REMOVE REAR DOOR SCUFF PLATE LH
Disengage the 5 claws and guide and remove the rear door scuff plate LH.
67914
3.REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 8 claws and remove the front door scuff plate LH.
62112
4.REMOVE COWL SIDE TRIM BOARD LH
Remove the clip.
Disengage the clip and remove the cowl side trim board LH.
62312B
5.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH.
62212
6.REMOVE FRONT PILLAR GARNISH LH
|
Protective Tape |
Apply protective tape around the front pillar garnish LH as shown in the illustration.
| *1 | Front Pillar Garnish Clip |
Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.
Let the front pillar garnish LH hang from the front pillar garnish clip.
| *1 | Front Pillar Garnish Clip |
While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.
The front pillar garnish clip is reusable if it is not damaged.
If the front pillar garnish clip is damaged, replace it with a new one.
When the front pillar garnish clip cannot be disengaged easily:
| *a | Tab |
While pushing the tab of the front pillar garnish clip with your finger, move the front pillar garnish clip in the direction shown in the illustration.
| *a | Tab |
While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip with a screwdriver and disengage the front pillar garnish clip.
Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.
| *1 | Curtain Shield Airbag Assembly LH |
| *a | Protective Cover |
| *b | Adhesive Tape |
Protect the curtain shield airbag assembly LH.
Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.
62332A
7.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Remove the rear door opening trim weatherstrip LH.
73233C
8.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
73220
9.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
62414A
10.REMOVE CENTER PILLAR LOWER GARNISH LH
Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.
62412B
11.REMOVE CENTER PILLAR UPPER GARNISH LH
Remove the 2 screws and disengage the clip.
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.
67917A
12.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
67913
13.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62111C
14.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
62311B
15.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62211
16.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62331A
17.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
73233
18.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)
Use the same procedure as for the LH side.
73210
19.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62413A
20.REMOVE CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
62411B
21.REMOVE CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
58410B
22.REMOVE DECK BOARD ASSEMBLY (w/o Coat Hook)
Remove the deck board assembly.
64997
23.REMOVE DECK FLOOR BOX LH (w/o Coat Hook)
Remove the deck floor box LH.
64995
24.REMOVE DECK FLOOR BOX RH (w/o Coat Hook)
Use the same procedure as for the LH side.
58570A
25.REMOVE REAR FLOOR MAT ASSEMBLY (w/ Coat Hook)
Remove the rear floor mat assembly.
64777J
26.REMOVE SPARE WHEEL CUSHION (w/ Coat Hook)
Remove the 2 spare wheel cushions.
64330D
27.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Remove the package tray trim panel assembly.
64716D
28.REMOVE REAR DECK TRIM COVER (w/o Coat Hook)
Remove the 2 clips.
Disengage the 4 claws and 4 guides to remove the rear deck trim cover.
64716D
29.REMOVE REAR DECK TRIM COVER (w/ Coat Hook)
Remove the 2 clips.
Disengage the 4 claws and 2 guides to remove the rear deck trim cover.
73370
30.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
58732C
31.REMOVE REAR ABSORBER CAP LH
Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.
81330
32.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
64740C
33.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.
| *1 | Rear Seatback Hinge | - | - |
Remove the bolt and 2 screws.
Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.
62472A
34.REMOVE ROOF SIDE INNER GARNISH LH
Disengage the 5 clips.
Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH and remove the roof side inner garnish LH.
73360
35.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
58731C
36.REMOVE REAR ABSORBER CAP RH
Use the same procedure as for the LH side.
64730B
37.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
73350
38.DISCONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
62471A
39.REMOVE ROOF SIDE INNER GARNISH RH
Using a moulding remover, disengage the 4 claws and guide, and disconnect the belt guide.
Disengage the 5 clips.
Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH and remove the roof side inner garnish RH.
81260A
40.REMOVE MAP LIGHT ASSEMBLY
81240
41.REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/ Room Light)
74610S
42.REMOVE ASSIST GRIP ASSEMBLY
Use the same procedure to remove all assist grips.
Using a moulding remover, disengage the 4 claws and remove the 2 assist grip covers.
Disengage the 2 clips and remove the assist grip.
74631C
43.REMOVE COAT HOOK (w/ Coat Hook)
Use the same procedure to remove all coat hooks.
| *a | Protective Tape |
Using a screwdriver, disengage the 3 claws to remove the cover.
Tape the screwdriver tip before use.
Disengage the clip to remove the coat hook.
74320
44.REMOVE VISOR ASSEMBLY LH
Disconnect the visor shaft from the visor holder.
Remove the 2 screws and the visor assembly LH.
74310
45.REMOVE VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74348
46.REMOVE VISOR HOLDER
Turn the visor holder 45° clockwise and disengage the 2 claws to remove the visor holder.
Use the same procedure for the LH side and RH side.
47.REMOVE ROOF HEADLINING ASSEMBLY
for front pillar RH side:
Disconnect the connector.
| *A | Front Pillar RH Side | *B | Front Pillar LH Side |
| *C | Rear Pillar RH Side | - | - |
|
Connector |
|
Bolt |
|
Clip | - | - |
Using a clip remover, disengage the 3 clamps.
for front pillar LH side:
Disconnect the connector.
Using a clip remover, disengage the 3 clamps.
for rear pillar RH side:
Disconnect the connector.
Remove the bolt and disconnect the connector bracket.
Using a clip remover, disengage the 2 clamps.
Using a clip remover, remove the 3 clips.
Disengage the 2 claws.
Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
Do not damage the roof headlining assembly or vehicle interior.