Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278107 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89174A 1.INSTALL FRONT AIRBAG SENSOR

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296255E06
4.763,1.829 4.955,2.012 0.192,0.183 10 *b 1.4,1.829 1.592,2.012 0.192,0.183 10 *b 4.763,0.568 4.955,0.751 0.192,0.183 10 *a 1.4,0.568 1.592,0.751 0.192,0.183 10 *a

Text in Illustration
*a Incorrect *b Correct


d.

Insert the pin (stopper) into the body hole and install the front airbag sensor to the vehicle body with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the front airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the front airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the pin (stopper) is securely inserted into the body hole.

·

Tighten the nut while holding the front airbag sensor because the front airbag sensor pin (stopper) is easily damaged.




e.

Connect the connector to the front airbag sensor.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

H103068E01
2.448,1.792 2.448,1.385 false 2.188,0.76 2.302,0.281 2.302,0.281 2.427,0.281 false 2.385,0.99 2.635,0.625 2.635,0.625 2.76,0.625 true 2.479,0.146 2.938,0.344 0.458,0.198 10 false (A) 2.813,0.542 3.271,0.74 0.458,0.198 10 false *1 2.375,1.833 2.833,2.031 0.458,0.198 10 false *2 6.01,3.427 6.469,3.625 0.458,0.198 10 false *a

Text in Illustration
*1 White Housing Lock *2 Yellow CPA
*a Connection is Completed - -

HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.




f.

Check that there is no looseness in the installation parts of the front airbag sensor.


Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).