Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057037 METER / GAUGE / DISPLAY _0278095 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge malfunction via a direct line.

DTC No. DTC Detection Condition Trouble Area
B1500 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Fuel sender gauge operation malfunction


·

Harness or connector

·

Fuel sender gauge assembly

·

Combination meter assembly



WIRING DIAGRAM

E237325E01
5.258,2.928 7.094,3.275 1.835,0.347 10 Combination Meter Assembly 6.09,0.896 6.327,1.053 0.237,0.157 10 L 5.888,0.896 6.066,1.046 0.178,0.150 10 2 2.106,2.246 2.225,2.396 0.119,0.150 10 3 2.097,0.889 2.216,1.039 0.119,0.150 10 2 0.296,3.037 2.115,3.362 1.819,0.325 10 Fuel Suction Tube Assembly with Pump and Gauge 0.482,1.491 1.122,2.153 0.640,0.662 10 Fuel Sender Gauge Assembly 1.288,1.452 1.406,1.602 0.119,0.150 10 2 1.288,2.058 1.406,2.208 0.119,0.150 10 1 1.821,2.246 2.040,2.395 0.218,0.149 10 FE 1.849,0.886 2.050,1.042 0.201,0.156 10 FS 5.258,2.783 5.593,2.931 0.334,0.149 10 G1 0.296,2.887 0.890,3.033 0.594,0.146 10 M22

PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input/Min.: 0 L, Max.: 127.5 L 10th segment illuminated: 31.7 to 36.0 Unit: Liter
9th segment illuminated: 28.5 to 31.7
8th segment illuminated: 25.4 to 28.5
7th segment illuminated: 22.1 to 25.4
6th segment illuminated: 19.2 to 22.1
5th segment illuminated: 16.2 to 19.2
4th segment illuminated: 12.7 to 16.2
3rd segment illuminated: 9.8 to 12.7
2nd segment illuminated: 6.9 to 9.8
1st segment illuminated: 4.5 to 6.9

Result:
Result Proceed to
Fuel level data can be displayed on the GTS and DTC B1500 is output. A
Fuel level data cannot be displayed on the GTS. B




A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
a.

Disconnect the M22 fuel sender gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 (L) - M22-2 (FS) Always Below 1 Ω
G1-2 (L) - Body ground Always 10 kΩ or higher
M22-3 (FE) - Body ground Always Below 1 Ω




OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

b.
A307401E02
0.115,0.094 2.052,1.563 1.938,1.469 1.188,4.083 0.51,4.083 true 2.417,2.25 1.365,2.25 false 0.208,0.146 0.729,0.542 0.521,0.396 10 false *a 0.354,4 0.677,4.229 0.323,0.229 10 false E 1.177,2.167 1.396,2.396 0.219,0.229 10 false F

Check that the float moves smoothly between E and F.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float level is F (upper) 13.5 to 16.5 Ω
1 - 2 Float level is between F (upper) and E (lower) 13.5 to 414.5 Ω (Gradually changes)
1 - 2 Float level is E (lower) 405.5 to 414.5 Ω


Text in Illustration
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)



OK

4.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

NG

4.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
a.

Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

OK:

There is no deformation.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE