Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057037 METER / GAUGE / DISPLAY _0278095 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The meter ECU uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 13 Ω with the float at the full position, and 414 Ω with the float at the empty position. The meter outputs auxiliary battery voltage through two resistors that are mounted inside the meter ECU. The meter ECU measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the auxiliary battery voltage.


HINT:

The fuel level warning light will come on when the fuel level is below 4.7 liters (5.0 US qts, 4.1 Imp. qts).


WIRING DIAGRAM

E237325E01
5.258,2.928 7.094,3.275 1.835,0.347 10 Combination Meter Assembly 6.09,0.896 6.327,1.053 0.237,0.157 10 L 5.888,0.896 6.066,1.046 0.178,0.150 10 2 2.106,2.246 2.225,2.396 0.119,0.150 10 3 2.097,0.889 2.216,1.039 0.119,0.150 10 2 0.296,3.037 2.115,3.362 1.819,0.325 10 Fuel Suction Tube Assembly with Pump and Gauge 0.482,1.491 1.122,2.153 0.640,0.662 10 Fuel Sender Gauge Assembly 1.288,1.452 1.406,1.602 0.119,0.150 10 2 1.288,2.058 1.406,2.208 0.119,0.150 10 1 1.821,2.246 2.040,2.395 0.218,0.149 10 FE 1.849,0.886 2.050,1.042 0.201,0.156 10 FS 5.258,2.783 5.593,2.931 0.334,0.149 10 G1 0.296,2.887 0.890,3.033 0.594,0.146 10 M22

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge Empty, 1/2, Full -

OK:

Fuel receiver gauge indication is normal.




OK

2.READ VALUE USING GTS (FUEL INPUT)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input/Min.: 0 L, Max.: 127.5 L 10th segment illuminated: 31.7 to 36.0 Unit: Liter
9th segment illuminated: 28.5 to 31.7
8th segment illuminated: 25.4 to 28.5
7th segment illuminated: 22.1 to 25.4
6th segment illuminated: 19.2 to 22.1
5th segment illuminated: 16.2 to 19.2
4th segment illuminated: 12.7 to 16.2
3rd segment illuminated: 9.8 to 12.7
2nd segment illuminated: 6.9 to 9.8
1st segment illuminated: 4.5 to 6.9

Result:
Result Proceed to
Fuel level data displayed on the GTS differs from the fuel receiver gauge indication. A
Fuel level data displayed on the GTS is almost the same as the fuel receiver gauge indication. B




OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
a.

Disconnect the G1 combination meter assembly connector.


b.

Disconnect the M22 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 (L) - M22-2 (FS) Always Below 1 Ω
G1-2 (L) - Body ground Always 10 kΩ or higher
M22-3 (FE) - Body ground Always Below 1 Ω




OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

b.

Check that the float moves smoothly between E and F.


A307401E02
0.115,0.094 2.052,1.563 1.938,1.469 1.188,4.083 0.51,4.083 true 2.417,2.25 1.365,2.25 false 0.208,0.146 0.729,0.542 0.521,0.396 10 false *a 0.354,4 0.677,4.229 0.323,0.229 10 false E 1.177,2.167 1.396,2.396 0.219,0.229 10 false F

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float level is F (upper) 13.5 to 16.5 Ω
1 - 2 Float level is between F (upper) and E (lower) 13.5 to 414.5 Ω (Gradually changes)
1 - 2 Float level is E (lower) 405.5 to 414.5 Ω


Text in Illustration
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)



A

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

B

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
a.

Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

OK:

There is no deformation.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE