Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2018.08
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0451  Evaporative Emission Control System Pressure Sensor Range / Performance  P0452  Evaporative Emission Control System Pressure Sensor / Switch Low Input  P0453  Evaporative Emission Control System Pressure Sensor / Switch High Input  


DTC SUMMARY

DTC No. Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P0451 Canister pressure sensor abnormal voltage fluctuation Sensor output voltage fluctuates frequently in a certain time period.
·

Canister pump module

·

Connector/wire harness

(canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter or fuel tank vent hose)

·

ECM


·

EVAP monitoring (power switch off)

·

Engine running


2 trip
P0452 Canister pressure sensor low input EVAP pressure sensor less than 0.45 V for 0.5 seconds.
·

Power switch on (IG)

·

EVAP monitoring (power switch off)


1 trip
P0453 Canister pressure sensor high input EVAP pressure sensor higher than 4.9 V for 0.5 seconds.
·

Power switch on (IG)

·

EVAP monitoring (power switch off)


1 trip

HINT:

The canister pressure sensor is built into the canister pump module.


DESCRIPTION

The description can be found in EVAP (Evaporative Emission) System.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>EVAP System

MONITOR DESCRIPTION

A304708E05
4.563,3.302 5.063,3 false 4.563,1.417 5.063,1.115 false 0.167,0.167 2.771,0.448 2.604,0.281 10 false Canister Pressure Sensor Specification: 1.25,1 2.396,1.313 1.146,0.313 10 false Output Voltage 1.708,1.427 2.292,1.594 0.583,0.167 10 false 4.900 V 1.708,1.917 2.292,2.083 0.583,0.167 10 false 4.423 V 1.708,2.604 2.292,2.771 0.583,0.167 10 false 1.425 V 1.708,3.073 2.292,3.24 0.583,0.167 10 false 0.450 V 2.917,3.469 3.26,3.865 0.344,0.396 10 false 60 (450) 3.594,3.469 3.927,3.906 0.333,0.438 10 false 115 (863) 4.333,3.469 5.229,3.833 0.896,0.365 10 false kPa(abs) [mmHg(abs)] 5.302,3.333 5.969,3.5 0.667,0.167 10 false Pressure 5.115,2.917 6.198,3.083 1.083,0.167 10 false Malfunction Area 5.115,1.031 6.198,1.198 1.083,0.167 10 false Malfunction Area 3.833,2.333 4.885,2.594 1.052,0.26 10 false Usable Range 1.01,4.156 1.573,4.583 0.563,0.427 10 false HINT: 1,4.333 5.292,4.563 4.292,0.229 10 false Standard atmospheric pressure is 101.3 kPa(abs) [760 mmHg(abs)]

1.

DTC P0451: Canister pressure sensor abnormal voltage fluctuation

If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as the canister pressure sensor voltage fluctuating, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC.

(Malfunction is detected by 2 trip detection logic).

2.

DTC P0452: Canister pressure sensor voltage low

If the canister pressure sensor voltage output (pressure) is less than 0.45 V: 42.11009 kPa(abs) [315.82568 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).

3.

DTC P0453: Canister pressure sensor voltage high

If the canister pressure sensor voltage output (pressure) is higher than 4.9 V: 123.76147 kPa(abs) [928.21103 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).


MONITOR STRATEGY

Required Sensors/Components (Main) Canister pump module
Required Sensors/Components (Related) -
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the GTS. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is higher than 85% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature less than 35°C (95°F).



1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

4.

Check that the intake air temperature is between 4.4 and 50°C (40 and 122°F).

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the power switch off and wait for at least 30 seconds.

7.

Turn the power switch on (IG) and turn the GTS on.

8.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

9.

After the Evaporative System Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0451, P0452 or P0453.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A410650E01
5.823,0.542 6.281,0.74 0.458,0.198 10 false PRG 5.5,0.531 5.958,0.729 0.458,0.198 10 false C10 5.25,0.417 5.563,0.615 0.313,0.198 10 false 76 3.563,0.417 3.719,0.615 0.156,0.198 10 false 2 2.479,0.406 2.635,0.604 0.156,0.198 10 false 1 2.344,0.854 2.719,1.104 0.375,0.25 10 false C19 2.646,0.854 3.76,1.146 1.115,0.292 10 false Purge VSV 5.521,1.594 5.979,1.792 0.458,0.198 10 false A40 5.573,1.375 5.729,1.573 0.156,0.198 10 false 5 5.844,1.583 6.458,1.781 0.615,0.198 10 false VPMP 4.604,1.479 4.76,1.677 0.156,0.198 10 false 1 4.115,1.458 4.667,1.781 0.552,0.323 10 false VGND 2.823,1.76 3.771,2.052 0.948,0.292 10 false Vent Valve 2.615,1.469 3.104,1.74 0.49,0.271 10 false VLVB 2.406,1.438 2.563,1.635 0.156,0.198 10 false 5 2.417,2.208 2.573,2.406 0.156,0.198 10 false 4 2.604,2.177 3.188,2.458 0.583,0.281 10 false MGND 2.979,2.896 4.396,3.24 1.417,0.344 10 false Leak Detection Pump 4.094,2.167 4.531,2.49 0.438,0.323 10 false MTRB 4.604,2.146 4.76,2.344 0.156,0.198 10 false 3 5.51,2.302 5.969,2.5 0.458,0.198 10 false A40 5.531,2.115 5.844,2.313 0.313,0.198 10 false 18 5.833,2.302 6.448,2.5 0.615,0.198 10 false MPMP 2.854,3.302 3.406,3.938 0.552,0.635 10 false Canister Pressure Sensor 2.302,4.719 2.698,4.979 0.396,0.26 10 false M52 2.615,4.719 4.51,5.115 1.896,0.396 10 false Canister Pump Module 4.198,3.281 4.656,3.479 0.458,0.198 10 false VCC 4.573,3.281 4.729,3.479 0.156,0.198 10 false 6 4.125,3.677 4.74,3.875 0.615,0.198 10 false VOUT 4.594,3.656 4.75,3.854 0.156,0.198 10 false 7 4.104,4.083 4.625,4.354 0.521,0.271 10 false SGND 4.583,4.063 4.74,4.26 0.156,0.198 10 false 8 5.833,3.385 6.448,3.583 0.615,0.198 10 false VCPP 5.51,3.375 5.969,3.573 0.458,0.198 10 false A40 5.552,3.146 5.865,3.344 0.313,0.198 10 false 34 5.833,3.781 6.448,3.979 0.615,0.198 10 false PPMP 5.542,3.604 5.854,3.802 0.313,0.198 10 false 35 5.521,3.781 5.979,3.979 0.458,0.198 10 false A40 5.844,4.208 6.458,4.406 0.615,0.198 10 false EPPM 5.51,4.198 5.969,4.396 0.458,0.198 10 false A40 5.531,4.021 5.844,4.219 0.313,0.198 10 false 36 4.25,5.573 5.083,5.979 0.833,0.406 10 false EFI NO. 2 3.073,6.063 3.385,6.26 0.313,0.198 10 false 2C 3.125,5.854 3.281,6.052 0.156,0.198 10 false 4 1.979,6.771 2.76,7.083 0.781,0.313 10 false EFI-MAIN 1.375,6.24 2.135,6.542 0.76,0.302 10 false EFI-MAIN 1.073,6.073 1.385,6.271 0.313,0.198 10 false 2E 1.083,5.875 1.24,6.073 0.156,0.198 10 false 1 0.594,6.531 1.021,6.781 0.427,0.25 10 false P/I 0.594,7.229 1.115,7.5 0.521,0.271 10 false MAIN 0.75,7.979 1.938,8.302 1.188,0.323 10 false Auxiliary Battery 1.844,7.135 2.854,7.51 1.01,0.375 10 false No. 1 Integration Relay 1.5,6.875 1.813,7.073 0.313,0.198 10 false 2C 1.323,6.865 1.479,7.063 0.156,0.198 10 false 2 2.927,6.885 3.24,7.083 0.313,0.198 10 false 2C 2.75,6.865 2.906,7.063 0.156,0.198 10 false 3 5.51,7.479 5.875,7.74 0.365,0.26 10 false A40 5.51,7.271 5.823,7.469 0.313,0.198 10 false 46 5.823,7.365 6.313,7.646 0.49,0.281 10 false MREL 6.188,8.156 6.656,8.417 0.469,0.26 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.

·

The GTS is required to conduct the following diagnostic troubleshooting procedure.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CONFIRM DTC AND EVAP PRESSURE
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) (do not start the engine).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Evaporative / Vapor Pressure Pump.


g.

Read the EVAP (Evaporative Emission) pressure displayed on the GTS.

Result
Display (DTC Output) Test Result Suspected Trouble Area Proceed to
P0451 - Canister pressure sensor C
P0452 Less than 42.11009 kPa(abs) [315.82568 mmHg(abs)]
·

Wire harness/connector (ECM - canister pressure sensor)

·

Canister pressure sensor

·

Short in ECM circuit


A
P0453 Higher than 123.76147 kPa(abs) [928.21103 mmHg(abs)]
·

Wire harness/connector (ECM - canister pressure sensor)

·

Canister pressure sensor

·

Open in ECM circuit


B



A

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

C

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A40-35 (PPMP) - Body ground Always Below 10 Ω
·

Wire harness/connector (ECM - canister pressure sensor)

·

Short in canister pressure sensor circuit


A
10 kΩ or higher
·

Wire harness/connector (ECM - canister pressure sensor)

·

Short in ECM circuit


B



A

3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the canister pump module connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A40-35 (PPMP) - Body ground Always 10 kΩ or higher Short in canister pressure sensor circuit A
Below 10 Ω Short in wire harness/connector (ECM - canister pressure sensor) B



A

5.REPLACE CANISTER PUMP MODULE

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the canister pump module connector.

U159108E03
5.823,1.729 5.823,2.25 false 5.656,1.729 5.333,2.156 false 5.99,1.729 6.229,2.167 false 4.625,1.396 4.927,1.552 0.302,0.156 10 false M52 5.635,2.26 6.094,2.417 0.458,0.156 10 false VOUT 4.802,0.271 5.104,0.427 0.302,0.156 10 false *a 5.115,2.198 5.573,2.354 0.458,0.156 10 false VCC 6.135,2.208 6.594,2.365 0.458,0.156 10 false SGND

Text in Illustration
*a Front view of wire harness connector
(to Canister Pump Module)
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M52-8 (SGND) - Body ground Always 100 Ω or less



c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M52-6 (VCC) - Body ground Power switch on (IG) 4.5 to 5.5 V
M52-7 (VOUT) - Body ground Power switch on (IG) 4.5 to 5.5 V


Result
Test Result Suspected Trouble Area Proceed to
Voltage and resistance within standard ranges Open in canister pressure sensor circuit A
Voltage and/or resistance outside standard ranges Open in wire harness/connector (ECM - canister pressure sensor) B



A

5.REPLACE CANISTER PUMP MODULE

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
5.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module.

Click hereEngine / Hybrid System>1NZ-FXE EMISSION CONTROL>CANISTER(w/ Canister Pump Module)>REMOVAL

NOTICE:
·

When replacing the canister pump module, check the canister pump module interior, canister interior and No. 1 canister interior related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior or No. 1 canister interior, replace the canister, No. 1 canister and canister pump module together.

·

Check for filter blockage in the canister and No. 1 canister. If the charcoal filter inside the canister or No. 1 canister is clogged, replace the canister, No. 1 canister and canister pump module together.

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.



U159111E02
2.75,1.281 2.896,0.958 2.896,0.958 3.052,0.958 false 5.302,4.135 5.438,4.01 5.438,4.01 5.521,4.01 false 5.448,5.031 5.646,5.208 5.646,5.208 5.74,5.208 false 5.448,5.406 5.583,5.521 5.583,5.521 5.667,5.521 false 5.24,2.896 5.49,2.698 5.49,2.698 5.646,2.698 false 4.375,2.385 4.583,1.698 4.583,1.698 4.792,1.698 false 3.729,3.802 3.458,4.75 3.458,4.75 3.625,4.75 false 4.948,2.135 6.583,2.135 false 5.479,5.01 6.573,5.01 false 6.427,5 6.427,2.188 false 4.427,5.281 3.323,5.281 false 5.323,3.448 5.469,3.448 false 3.281,2.75 3.281,5.49 false 4.479,3.323 4.479,5.427 false 3.125,0.875 3.427,1.073 0.302,0.198 10 false *4 5.542,3.375 5.844,3.573 0.302,0.198 10 false *5 6.531,3.375 6.833,3.573 0.302,0.198 10 false *a 4.875,1.635 5.177,1.833 0.302,0.198 10 false *6 5.552,3.958 5.854,4.156 0.302,0.198 10 false *3 5.802,5.135 6.104,5.333 0.302,0.198 10 false *2 5.708,5.469 6.01,5.667 0.302,0.198 10 false *8 5.698,2.615 6,2.813 0.302,0.198 10 false *7 3.698,4.708 4,4.906 0.302,0.198 10 false *1 3.813,5.271 4.115,5.469 0.302,0.198 10 false *a

Text in Illustration
*1 Fuel Tank Vent Hose *2 Air Inlet Port
*3 Vent Hose *4 Fuel Tank
*5 Canister Pump Module *6 Canister
*7 No. 1 Canister *8 Canister Filter
*a Inspection Area
(check for disconnection and/or cracks)
- -



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0451, P0452 OR P0453)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)
HINT:

If the exhaust pipe has been removed, go to the next step before reinstalling it.



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0451, P0452 OR P0453)
7.REPLACE ECM

NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0451, P0452 OR P0453)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0451, P0452 OR P0453)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Perform the Evaporative System Check using the GTS, referring to the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0451, P0452 or P0453.


k.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





NEXT

END