Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2018.08
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights.

WIRING DIAGRAM

C406213E01
5.969,0.719 6.365,0.875 0.396,0.156 10 false CA1L 5.698,0.625 5.979,0.781 0.281,0.156 10 false 38 5.698,1.542 5.885,1.698 0.188,0.156 10 false 37 4.198,0.51 4.385,0.667 0.188,0.156 10 false 24 4.198,1.427 4.385,1.583 0.188,0.156 10 false 25 2.927,0.99 3.146,1.146 0.219,0.156 10 false 28 5.969,1.635 6.385,1.792 0.417,0.156 10 false CA1H 3.656,0.729 4.052,0.885 0.396,0.156 10 false CA1L 3.635,1.667 4.052,1.823 0.417,0.156 10 false CA1H 0.969,1.198 1.177,1.354 0.208,0.156 10 false TC 3.271,1.208 3.479,1.365 0.208,0.156 10 false TC 1.313,1 1.49,1.156 0.177,0.156 10 false 13 1.375,3 1.49,3.167 0.115,0.167 10 false 4 0.958,3.208 1.198,3.365 0.24,0.156 10 false CG 0.615,4.135 1,4.292 0.385,0.156 10 false DLC3 2.771,4.125 4.542,4.5 1.771,0.375 10 false Hybrid Vehicle Control ECU 5.01,4.115 7.115,4.479 2.104,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.146,0.719 4.448,0.875 0.302,0.156 10 false G81 4.146,1.635 4.531,1.792 0.385,0.156 10 false G81 2.875,1.188 3.198,1.344 0.323,0.156 10 false G81 5.969,2.625 6.365,2.781 0.396,0.156 10 false CA2L 5.698,2.531 5.885,2.688 0.188,0.156 10 false 34 5.698,3.448 5.885,3.604 0.188,0.156 10 false 35 4.198,2.396 4.385,2.552 0.188,0.156 10 false 30 4.208,3.344 4.396,3.5 0.188,0.156 10 false 31 5.969,3.573 6.385,3.729 0.417,0.156 10 false CA2H 3.646,2.635 4.042,2.792 0.396,0.156 10 false CA3N 3.667,3.573 4.083,3.729 0.417,0.156 10 false CA3P 4.146,2.615 4.448,2.771 0.302,0.156 10 false G81 4.146,3.552 4.521,3.708 0.375,0.156 10 false G81 4.688,4.125 4.99,4.281 0.302,0.156 10 false A41 1.271,1.198 1.604,1.375 0.333,0.177 10 false G93 1.74,1.198 2.073,1.375 0.333,0.177 10 false G4 1.74,1 1.917,1.156 0.177,0.156 10 false 13 1.292,3.208 1.625,3.385 0.333,0.177 10 false G93 1.76,3.208 2.094,3.385 0.333,0.177 10 false G4 1.813,3 1.927,3.167 0.115,0.167 10 false 4 1.344,3.448 1.531,3.625 0.188,0.177 10 false *1 1.76,3.438 1.948,3.615 0.188,0.177 10 false *2 1.313,1.417 1.5,1.594 0.188,0.177 10 false *1 1.76,1.417 1.948,1.594 0.188,0.177 10 false *2 1.375,4.521 2.26,4.729 0.885,0.208 10 false *1: for LHD 2.26,4.521 3.146,4.729 0.885,0.208 10 false *2: for RHD

HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - HYBRID VEHICLE CONTROL ECU)

B

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G93-13 (TC) - G81-28 (TC) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
G4-13 (TC) - G81-28 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C406212C02
1.51,0.844 1.885,1.083 0.375,0.24 1.51,1.208 1.885,1.448 0.375,0.24 1.646,1.927 2.479,1.229 false 0.313,0.281 0.625,0.479 0.313,0.198 10 false *a 1.604,1.25 1.917,1.448 0.313,0.198 10 false G4 1.563,0.885 1.875,1.083 0.313,0.198 10 false G93 1.948,0.885 2.26,1.083 0.313,0.198 10 false *1 1.958,1.24 2.271,1.438 0.313,0.198 10 false *2 2.479,1.052 2.792,1.25 0.313,0.198 10 false CG
*1 for LHD
*2 for RHD
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G93-4 (CG) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
G4-4 (CG) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)
a.
C406212C10
1.51,0.844 1.885,1.083 0.375,0.24 1.51,1.208 1.885,1.448 0.375,0.24 1.833,2.375 2.479,1.146 false 0.313,0.281 0.625,0.479 0.313,0.198 10 false *a 1.604,1.25 1.917,1.448 0.313,0.198 10 false G4 1.563,0.885 1.875,1.083 0.313,0.198 10 false G93 1.948,0.885 2.26,1.083 0.313,0.198 10 false *1 1.958,1.24 2.271,1.438 0.313,0.198 10 false *2 2.448,0.948 2.76,1.146 0.313,0.198 10 false TC
*1 for LHD
*2 for RHD
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G93-13 (TC) or G81-28 (TC) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G4-13 (TC) or G81-28 (TC) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE WIRE HARNESS OR EACH ECU