Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor for the intake camshaft (G2 signal) consists of a magnet and MRE (Magneto Resistance Element).

The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration and injection timing.

DTC No. DTC Detection Condition Trouble Area
P0340 When either of following conditions is met (1 trip detection logic):
·

No camshaft position sensor signal to ECM at engine speed 600 rpm or higher

·

Missing camshaft position sensor signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or higher


·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Intake camshaft

·

Valve timing

·

ECM


P0342 Output voltage of camshaft position sensor less than 0.3 V (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

ECM


P0343 Output voltage of camshaft position sensor higher than 4.7 V (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

ECM



A254147E01
2.986,0.993 3.323,1.140 0.336,0.147 10 GND 1.159,1.916 1.902,2.062 0.744,0.147 10 20 ms./DIV. 2.748,0.059 3.284,0.206 0.536,0.147 10 5 V/DIV.

Reference: Inspection using an oscilloscope.

HINT:

The correct waveform is as shown.


ECM Terminal Name Between G2+ and G2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

If no signal is transmitted by the camshaft position sensor despite the engine revolving, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

Idle the engine for 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0340, P0342 or P0343.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255253E83
1.083,1.927 1.417,2.073 0.333,0.146 10 false D18 1.083,2.083 4.219,2.281 3.135,0.198 10 false Camshaft Position Sensor (for Intake Camshaft) 5.177,0.427 5.573,0.573 0.396,0.146 10 false VCV1 5.708,2.198 6.031,2.375 0.323,0.177 10 false D28 5.708,2.365 6.052,2.552 0.344,0.188 10 false ECM 4.885,0.417 5.167,0.604 0.281,0.188 10 false 99 4.896,0.958 5.104,1.156 0.208,0.198 10 false 76 4.823,1.49 5.073,1.656 0.25,0.167 10 false 122 2.646,0.396 2.771,0.563 0.125,0.167 10 false 3 2.646,0.948 2.75,1.125 0.104,0.177 10 false 1 2.646,1.49 2.75,1.635 0.104,0.146 10 false 2 2.323,0.406 2.542,0.583 0.219,0.177 10 false VC 2.219,0.948 2.552,1.094 0.333,0.146 10 false VVI+ 2.24,1.49 2.531,1.625 0.292,0.135 10 false VVI- 5.177,0.969 5.552,1.135 0.375,0.167 10 false G2+ 5.177,1.5 5.552,1.667 0.375,0.167 10 false G2- 1.604,0.896 1.74,1.063 0.135,0.167 10 false * 0.063,2.417 4.396,2.604 4.333,0.188 10 false *: MRE (Outputs a voltage corresponding to changes in magnetic flux)

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR)
a.
U110411E02
1.99,2.51 2.271,3.073 false 0.208,0.198 0.396,0.375 0.188,0.177 10 false *a 0.479,2.375 0.802,2.542 0.323,0.167 10 false D18 2.208,3.104 2.531,3.271 0.323,0.167 10 false VC

Disconnect the camshaft position sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D18-3 (VC) - Body ground Power switch on (IG) 4.5 to 5.0 V


Text in Illustration
*a Front view of wire harness connector
(to Camshaft Position Sensor)



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-1 (VVI+) - D28-76 (G2+) Always Below 1 Ω
D18-2 (VVI-) - D28-122 (G2-) Always Below 1 Ω
D18-1 (VVI+) or D28-76 (G2+) - Body ground Always 10 kΩ or higher
D18-2 (VVI-) or D28-122 (G2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.
A352601E02
1.656,1.563 2.5,1.802 0.844,0.24 10 false Clearance 0.5,1.698 0.906,1.938 0.406,0.24 10 false OK 2.656,1.813 3.427,2.177 0.771,0.365 10 true NG

Check the camshaft position sensor installation.

OK:

Camshaft position sensor is installed correctly.




OK

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Timing rotor does not have any cracks or deformation.




OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

5.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (P0340, P0342 OR P0343)
6.CHECK WHETHER DTC OUTPUT RECURS (P0340, P0342 OR P0343)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine.


j.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


l.

Read the DTCs.

Result
Result Proceed to
DTC P0340, P0342 or P0343 is output A
DTC is not output B



A

7.ADJUST VALVE TIMING

B

END

7.ADJUST VALVE TIMING

NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (P0340, P0342 OR P0343)
8.CHECK WHETHER DTC OUTPUT RECURS (P0340, P0342 OR P0343)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine.


j.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


l.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0340, P0342 or P0343 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B

9.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-3 (VC) - D28-99 (VCV1) Always Below 1 Ω
D18-3 (VC) or D28-99 (VCV1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR