Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P2195).

HINT:
·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the power switch is turned off.

·

Although the DTC titles say the oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

The ECM uses pulse width modulated control to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A259006E06
0.119,0.131 2.743,0.303 2.623,0.172 10 Reference (System Diagram of Sensor 1): 0.088,1.142 0.631,1.672 0.544,0.530 10 from Auxiliary Battery 0.777,1.353 1.565,1.504 0.789,0.151 10 EFI MAIN 1.769,2.457 2.410,2.608 0.641,0.151 10 EFI MAIN 2.569,1.292 3.290,1.443 0.721,0.151 10 EFI NO. 2 0.731,3.361 1.230,3.507 0.498,0.147 10 Ground 3.557,0.853 4.013,1.004 0.457,0.151 10 Heater 3.557,1.423 4.036,1.574 0.480,0.151 10 Sensor 3.148,1.057 3.350,1.207 0.202,0.150 10 +B 3.031,1.617 3.400,1.782 0.369,0.164 10 A1A- 4.208,1.057 4.614,1.207 0.406,0.150 10 HA1A 4.208,1.613 4.614,1.763 0.406,0.150 10 A1A+ 5.119,1.085 5.525,1.235 0.406,0.150 10 HA1A 5.119,2.211 5.525,2.361 0.406,0.150 10 A1A- 5.119,2.785 5.525,2.935 0.406,0.150 10 MREL 5.119,1.641 5.525,1.791 0.406,0.150 10 A1A+ 3.188,2.095 4.568,2.242 1.380,0.147 10 Air Fuel Ratio Sensor 6.349,1.74 6.829,2.072 0.480,0.332 10 Duty Control 5.916,3.507 6.246,3.656 0.330,0.149 10 ECM 4.841,1.525 5.200,1.792 0.360,0.267 10 * 3.16,3.137 4.195,3.570 1.036,0.434 10 *: Shielded



DTC No. DTC Detection Condition Trouble Area
P0031 Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
·

Open in air fuel ratio sensor (sensor 1) heater circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P0032 An air fuel ratio sensor heater current reaches the high limit (Hybrid IC high current limiter input "Fail") (1 trip detection logic).
·

Short in air fuel ratio sensor (sensor 1) heater circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P101D The heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

P0031
Heater output duty cycle 30% or higher

P0032
Heater output duty cycle Higher than 0%

P101D
Air fuel ratio sensor heater duty-cycle 10% or higher, and less than 60%
Air fuel ratio sensor heater ON current 0.8 A or higher

CONFIRMATION DRIVING PATTERN

A198819E11
0.749,0.969 1.396,1.162 0.647,0.193 10 2500 rpm 0.946,1.739 1.352,1.900 0.406,0.161 10 Idling 0.423,2.006 1.317,2.323 0.894,0.317 10 Power Switch on (IG) 1.926,2.132 2.161,2.297 0.235,0.165 10 [A] 2.762,1.623 2.955,1.815 0.193,0.193 10 [B] 4.026,0.868 4.283,1.006 0.258,0.137 10 [C] 5.39,1.6 5.613,1.782 0.223,0.181 10 [D] 2.272,2.589 3.465,2.745 1.193,0.156 10 5 minutes or more 4.873,2.608 6.066,2.764 1.193,0.156 10 5 minutes or more 3.85,2.617 4.423,2.782 0.573,0.165 10 1 minute 5.98,3.028 6.182,3.230 0.202,0.202 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on [A].

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and idle it for 5 minutes or more [B].

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 2500 rpm for 1 minute [C].

HINT:

During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform steps [C] and [D] after charging control has completed.


9.

Idle the engine for 5 minutes or more [D].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0031, P0032 or P101D.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

A249515E14
4.853,3.625 4.961,3.775 0.108,0.150 10 1 3.847,3.625 4.046,3.775 0.199,0.150 10 +B 4.401,3.625 4.794,3.775 0.393,0.150 10 HT1B 4.397,4.289 4.812,4.440 0.415,0.150 10 OX1B 3.858,4.289 4.067,4.440 0.209,0.150 10 E2 3.681,3.625 3.790,3.775 0.108,0.150 10 2 3.691,4.355 3.799,4.505 0.108,0.150 10 4 4.851,4.354 4.959,4.504 0.108,0.150 10 3 3.72,0.947 3.829,1.097 0.108,0.150 10 2 3.865,0.947 4.063,1.097 0.199,0.150 10 +B 4.426,0.947 4.819,1.097 0.393,0.150 10 HA1A 4.47,1.637 4.834,1.787 0.364,0.150 10 A1A+ 3.865,1.637 4.199,1.787 0.334,0.150 10 A1A- 4.869,0.947 4.978,1.097 0.108,0.150 10 1 4.869,1.689 4.978,1.839 0.108,0.150 10 3 3.72,1.689 3.828,1.839 0.108,0.150 10 4 3.583,2.208 3.865,2.359 0.282,0.150 10 D24 3.583,2.373 4.945,2.710 1.362,0.337 10 Air Fuel Ratio Sensor (Bank 1 Sensor 1) 3.529,4.83 3.811,4.980 0.282,0.150 10 D9 3.529,4.994 5.030,5.332 1.501,0.337 10 Heated Oxygen Sensor (Bank 1 Sensor 2) 5.575,4.208 5.716,4.344 0.141,0.136 10 * 5.322,1.555 5.464,1.691 0.141,0.136 10 * 2.107,6.223 2.828,6.408 0.721,0.185 10 *: Shielded 0.595,5.726 1.162,6.084 0.567,0.358 10 Auxiliary Battery 0.435,4.31 0.787,4.471 0.352,0.161 10 P/I 1 0.416,2.482 1.068,2.644 0.652,0.161 10 EFI MAIN 1.372,2.115 2.013,2.276 0.640,0.161 10 EFI MAIN 0.435,5.041 0.910,5.203 0.476,0.161 10 MAIN 2.64,1.211 3.070,1.535 0.431,0.324 10 EFI NO. 2 5.977,5.908 6.116,6.058 0.139,0.150 10 6 5.883,6.073 6.148,6.223 0.265,0.150 10 A57 5.926,0.855 6.107,1.005 0.180,0.150 10 18 5.882,1.033 6.155,1.183 0.272,0.150 10 D28 5.89,1.61 6.140,1.761 0.250,0.150 10 103 5.882,1.775 6.157,1.925 0.275,0.150 10 D28 5.89,3.031 6.140,3.182 0.250,0.150 10 126 5.882,3.196 6.160,3.346 0.278,0.150 10 D28 5.938,3.544 6.111,3.694 0.173,0.150 10 41 5.882,3.706 6.160,3.856 0.278,0.150 10 D28 5.887,4.283 6.165,4.433 0.277,0.150 10 125 5.882,4.447 6.155,4.598 0.272,0.150 10 D28 5.888,5.484 6.186,5.634 0.298,0.150 10 102 5.882,5.656 6.156,5.806 0.274,0.150 10 D28 6.379,6.414 6.706,6.565 0.327,0.150 10 ECM 6.198,5.658 6.574,5.808 0.376,0.150 10 O1B- 6.198,4.447 6.625,4.598 0.427,0.150 10 OX1B 6.198,3.604 6.625,3.754 0.427,0.150 10 HT1B 6.198,3.117 6.634,3.268 0.436,0.150 10 A1A- 6.198,1.681 6.593,1.832 0.394,0.150 10 A1A+ 6.198,0.932 6.593,1.083 0.394,0.150 10 HA1A 6.198,5.99 6.641,6.140 0.443,0.150 10 MREL 2.23,0.851 2.405,1.014 0.174,0.163 10 4 0.549,3.121 0.723,3.284 0.174,0.163 10 1 1.417,3.121 1.592,3.284 0.174,0.163 10 3 1.838,3.121 2.012,3.284 0.174,0.163 10 2 2.185,1.037 2.424,1.220 0.239,0.184 10 1B 0.247,3.132 0.477,3.315 0.230,0.184 10 1C 1.111,3.132 1.340,3.315 0.230,0.184 10 1B 2.031,3.132 2.261,3.315 0.230,0.184 10 1B 1.296,3.375 2.026,3.880 0.731,0.505 10 No. 2 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F Heater Duty #1] (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
a.
U154354E03
1.927,2.031 2.479,1.625 false 0.896,2.083 1.167,2.26 0.271,0.177 10 false D24 0.531,0.115 0.698,0.271 0.167,0.156 10 false *a 2.479,1.458 2.708,1.615 0.229,0.156 10 false +B

Disconnect the air fuel ratio sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D24-2 (+B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor (Sensor 1))



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - EFI MAIN RELAY)

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D24-1 (HA1A) - D28-18 (HA1A) Always Below 1 Ω
D24-1 (HA1A) or D28-18 (HA1A) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0031, P0032 or P101D is output B



A

B