Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2013.08
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

HINT:

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.


The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and is integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrow. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A234900E54
1.594,2.99 0.958,2.51 true 1.802,2.979 2.073,2.677 false 2.917,1.813 3.521,0.729 true 3.052,1.792 3.594,1.417 true 3.198,2.219 3.688,1.813 true 2.844,2.427 3.573,2.229 3.573,2.229 2.99,2.427 true 3.052,2.51 3.479,2.781 true 0.156,3.323 0.99,3.667 0.833,0.344 10 false Exhaust Gas 0.438,2.375 0.979,2.708 0.542,0.333 10 false Element 2.104,2.573 2.5,2.875 0.396,0.302 10 false Cover 1.125,3.448 1.271,3.646 0.146,0.198 10 false A 2.01,3.448 2.156,3.646 0.146,0.198 10 false A 3.552,0.646 4.708,1.292 1.156,0.646 10 false Solid Electrolyte (Zirconia Element) 3.625,1.313 4.448,1.615 0.823,0.302 10 false Alumina 3.729,1.708 4.719,1.99 0.99,0.281 10 false Heater 3.615,2.146 5.031,2.49 1.417,0.344 10 false Platinum Electrode 3.521,2.719 4.594,3.063 1.073,0.344 10 false Atmospheric Air 2.583,3.188 3.75,3.552 1.167,0.365 10 false A-A Cross Section 5.677,3.167 6.573,3.51 0.896,0.344 10 false Air Fuel Ratio 5.104,0.667 6.969,1.26 1.865,0.594 10 false ECM Monitored Air Fuel Ratio Sensor Voltage

DTC No. DTC Detection Condition Trouble Area
P2195 Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

(a) Air fuel ratio sensor voltage higher than 3.8 V.

(b) Heated oxygen sensor voltage is 0.21 V or higher.


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

EGR valve assembly

·

ECM


While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

ECM


P2196 Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

(a) Air fuel ratio sensor voltage less than 2.8 V.

(b) Heated oxygen sensor voltage is less than 0.59 V.


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

EGR valve assembly

·

ECM


While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

ECM



HINT:
·

When any of these DTCs is stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / All Data / AFS Voltage B1S1.

·

Short-term fuel trim values can also be read using the GTS.

·

The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the GTS.

·

If an air fuel ratio sensor malfunction is detected, the ECM stores a DTC.



MONITOR DESCRIPTION

Sensor Voltage Detection Monitor

Under air fuel ratio feedback control, if the air fuel ratio sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor output voltage being less than 0.59 V, the ECM stores DTC P2196. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P2195 is stored.


Sensor Current Detection Monitor

A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.

If the air fuel ratio sensor output is 2.2 mA or higher for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P2195 (stuck on high side). If the air fuel ratio sensor output is less than 0.7 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 (stuck on low side).


A107165E96
2.365,2.292 2.198,1.563 2.198,1.563 2.302,1.563 false 4.375,2.292 4.208,1.563 4.208,1.563 4.313,1.563 false 5.771,2.292 5.688,1.583 5.688,1.583 5.771,1.583 false 0.177,0.083 3.125,0.281 2.948,0.198 10 false Air Fuel Ratio Sensor Current Monitor 2.896,0.375 6.646,0.573 3.75,0.198 10 false Cumulative Time "t" = t1 + t2 = 3 seconds or more 0.583,1.073 1.365,1.271 0.781,0.198 10 false Fuel-cut 1.49,0.927 1.802,1.125 0.313,0.198 10 false ON 1.438,1.208 1.854,1.406 0.417,0.198 10 false OFF 2.354,1.479 3.719,1.677 1.365,0.198 10 false Delay (3 seconds) 4.365,1.479 5.552,1.813 1.188,0.333 10 true Delay (3 seconds) 5.823,1.5 7.042,1.781 1.219,0.281 10 true Delay (3 seconds) 2.354,3.698 3.552,3.938 1.198,0.24 10 true 3 seconds or more 2.323,4.26 4.083,4.458 1.76,0.198 10 false Normal Sensor Output 4.625,4.271 6.292,4.469 1.667,0.198 10 false Abnormal Sensor Output 6.344,4.26 6.813,4.458 0.469,0.198 10 false Time 0.406,2.177 2.052,2.375 1.646,0.198 10 false Sensor Current (mA) 0.406,2.802 2.052,3 1.646,0.198 10 false High Side Threshold 0.458,3.469 2.021,3.667 1.563,0.198 10 false Low Side Threshold 4.688,3.792 4.906,3.99 0.219,0.198 10 false t1 6.01,3.792 6.229,3.99 0.219,0.198 10 false t2

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor
Duration 3 seconds: Sensor current detection monitor
5 seconds: Sensor voltage detection monitor

TYPICAL ENABLING CONDITIONS

Sensor Voltage Detection Monitor
Time after engine start 30 seconds or more
Fuel system status Closed loop

Sensor Current Detection Monitor
Auxiliary battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher
Air fuel ratio sensor status Activated
Continuous time of fuel-cut 3 seconds or more, and less than 10 seconds

TYPICAL MALFUNCTION THRESHOLDS

P2195: Sensor Voltage Detection Monitor (Lean Side Malfunction)
Heated oxygen sensor voltage 0.21 V or higher
Air fuel ratio sensor voltage Higher than 3.8 V

P2196: Sensor Voltage Detection Monitor (Rich Side Malfunction)
Heated oxygen sensor voltage Less than 0.59 V
Air fuel ratio sensor voltage Less than 2.8 V

P2195: Sensor Current Detection Monitor (High Side Malfunction)
Air fuel ratio sensor current 2.2 mA or higher

P2196: Sensor Current Detection Monitor (Low Side Malfunction)
Air fuel ratio sensor current Less than 0.7 mA

CONFIRMATION DRIVING PATTERN

A293210E17
2.469,1.51 2.917,0.76 2.917,0.76 2.708,0.76 false 4.438,1.521 5.052,1.521 false 4.479,0.771 4.896,1.781 false 5.76,0.74 5.469,1.729 false 5.688,2.26 6.365,2.26 false 4.698,3.01 4.969,3.01 4.969,3.01 5.083,2.729 false 5.094,3.208 5.344,3.208 5.344,3.208 5.5,2.729 false 3.958,3.354 4.344,3.51 false 0.031,0.25 3.031,0.51 3,0.26 10 false Engine Coolant Temperature: 75°C or higher 1.083,0.677 2.844,1.031 1.76,0.354 10 false Between 60 and 100 km/h 0.75,2.281 1.302,2.698 0.552,0.417 10 false Idling 1.292,2.771 2.208,3.208 0.917,0.438 10 false Waming up 2.49,2.792 3.198,3.302 0.708,0.51 10 false 10 minutes or more 0.177,0.917 1.219,1.292 1.042,0.375 10 false Vehicle Speed 1.344,2.146 1.76,2.531 0.417,0.385 10 false [A] 2.75,1.302 3.167,1.688 0.417,0.385 10 false [B] 3.521,2.135 3.938,2.521 0.417,0.385 10 false [C] 5.135,1.281 5.552,1.667 0.417,0.385 10 false [D] 5.51,1.646 5.927,2.031 0.417,0.385 10 false [E] 4.667,0.896 5.688,1.198 1.021,0.302 10 false At least 3 times 3.365,0.625 4.458,0.99 1.094,0.365 10 false Accelerator Pedal Depressed 3.406,1.427 4.479,1.688 1.073,0.26 10 false 60 km/h or more 5.802,0.604 7.01,1.042 1.208,0.438 10 false Accelerator Pedal Released (Fuel-cut) 6.417,2.177 6.969,2.438 0.552,0.26 10 false 10 km/h 6.208,2.573 6.76,2.833 0.552,0.26 10 false Time 3.448,2.917 4.844,3.24 1.396,0.323 10 false 10 seconds or more 3.906,3.125 5.302,3.448 1.396,0.323 10 false 4 seconds or more 4.417,3.427 5.813,3.719 1.396,0.292 10 false Refer to figure below 6.094,3.125 6.646,3.385 0.552,0.26 10 false [F]

A268862E45
3.635,2.625 3.948,0.885 false 3.354,2.635 2.146,0.729 2.146,0.729 2.271,0.729 false 0.104,0.042 3.042,0.24 2.938,0.198 10 false Driving Pattern Detail for [C] through [E]: 0.188,0.552 1.958,0.75 1.771,0.198 10 false Reference Engine Speed 2.823,0.156 6.979,0.354 4.156,0.198 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 1.083,2.396 1.5,2.594 0.417,0.198 10 false Idling 2.188,2.969 2.604,3.167 0.417,0.198 10 false Idling 3.198,3.104 3.854,3.469 0.656,0.365 10 false 4 seconds or more 2.188,2.25 2.406,2.448 0.219,0.198 10 false [C] 3.01,1.156 3.25,1.354 0.24,0.198 10 false [D] 3.469,1.542 3.667,1.74 0.198,0.198 10 false [E] 2.333,0.646 3.521,0.844 1.188,0.198 10 false Delay (3 seconds) 4.01,0.771 5.448,0.969 1.438,0.198 10 false Detection Period t1 4.813,2.417 4.969,2.615 0.156,0.198 10 false t2 6.031,2.417 6.188,2.615 0.156,0.198 10 false t3 6.49,2.781 6.875,2.979 0.385,0.198 10 false Time 4.375,3.104 5.031,3.469 0.656,0.365 10 false 4 seconds or more 5.615,3.104 6.271,3.469 0.656,0.365 10 false 4 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) and turn the GTS on.

7.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

9.

On the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / All Data / Idle Fuel Cut.

10.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

With shift state B selected [C], accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

HINT:

While "Idle Fuel Cut" on the Data List is ON, fuel-cut control is being executed.


13.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

14.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P2195 or P2196.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P2195 or P2196 is output A
DTC P2195 or P2196 and P0136, P0137 or P0138 are output A
DTC P2195 or P2196 and other DTCs are output B

HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

NO

4.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P2195 or P2196.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B



A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)
4.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1.


f.

Check the test value of the air fuel ratio sensor output current during fuel-cut, referring to the Driving Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.

HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.



Result
Result Proceed to
Within normal range (0.7 mA or higher, and lower than 2.2 mA) A
Outside normal range (lower than 0.7 mA, or 2.2 mA or higher) B



A

5.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)

B

16.REPLACE AIR FUEL RATIO SENSOR
5.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine.


f.

Warm up the engine and run the engine at an engine speed of 2500 rpm for 90 seconds.

HINT:

During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, warm up the engine after charging control has completed.



g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.


h.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


i.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Less than 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Less than 0.4 V

Result
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich A
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction B
Lean/Rich Lean/Rich Normal B

Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently less than 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage B1S1 is consistently less than 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and the heated oxygen sensor alternates correctly.


HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2] (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).




A

6.CHECK INTAKE SYSTEM

B

16.REPLACE AIR FUEL RATIO SENSOR
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in the intake system.




OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

8.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE

OK

9.INSPECT FUEL INJECTOR ASSEMBLY

NG

18.CHECK FUEL LINE
9.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL INJECTOR>INSPECTION).



OK

10.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.REPLACE AIR FUEL RATIO SENSOR

NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P2195 or P2196.


m.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B



A

12.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

END

12.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off and shift lever in P or N.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.


g.

Check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



Result
Result Proceed to
NG A
OK B



A

13.INSPECT EGR VALVE ASSEMBLY

B

14.REPLACE ECM
13.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.




OK

14.REPLACE ECM

NG

14.REPLACE ECM

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P2195 or P2196.


m.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





NEXT

END

16.REPLACE AIR FUEL RATIO SENSOR

NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P2195 or P2196.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B



A

END

B

18.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.



OK

NG

REPAIR OR REPLACE FUEL LINE