Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM J

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A259026E07
6.229,7.302 6.552,7.479 0.323,0.177 10 false ECM 5.469,0.75 5.719,0.927 0.25,0.177 10 false #10 5.469,2.031 5.719,2.208 0.25,0.177 10 false #20 5.469,3.271 5.719,3.448 0.25,0.177 10 false #30 5.469,4.521 5.719,4.698 0.25,0.177 10 false #40 5.469,5.583 5.729,5.76 0.26,0.177 10 false E01 5.469,6.177 5.729,6.354 0.26,0.177 10 false E02 5.188,0.75 5.438,0.927 0.25,0.177 10 false 85 5.188,2.031 5.438,2.208 0.25,0.177 10 false 84 5.188,3.271 5.438,3.448 0.25,0.177 10 false 83 5.188,4.521 5.438,4.698 0.25,0.177 10 false 82 3.865,4.521 4.031,4.698 0.167,0.177 10 false 1 4.5,4.521 4.667,4.698 0.167,0.177 10 false 2 3.844,3.271 4.01,3.448 0.167,0.177 10 false 1 4.521,3.271 4.688,3.448 0.167,0.177 10 false 2 3.844,2.031 4.01,2.208 0.167,0.177 10 false 1 2.531,0.667 2.698,0.844 0.167,0.177 10 false 4 2.542,1.146 2.708,1.323 0.167,0.177 10 false 3 4.521,2.031 4.688,2.208 0.167,0.177 10 false 2 3.844,0.75 4.01,0.927 0.167,0.177 10 false 1 4.521,0.75 4.688,0.927 0.167,0.177 10 false 2 5.125,5.583 5.375,5.76 0.25,0.177 10 false 109 5.198,6.177 5.365,6.354 0.167,0.177 10 false 81 3.531,1.115 5.042,1.427 1.51,0.313 10 false D14 3.5,2.365 4.979,2.688 1.479,0.323 10 false D15 3.5,3.625 5,3.969 1.5,0.344 10 false D16 3.51,4.885 4.99,5.198 1.479,0.313 10 false D17 0.396,2.083 0.656,2.26 0.26,0.177 10 false IG2 0.417,5.01 0.729,5.188 0.313,0.177 10 false P/I 1 1.719,1.688 1.958,1.865 0.24,0.177 10 false IG2 1.521,5.219 1.865,5.396 0.344,0.177 10 false L195 1.521,5.396 2.635,6.031 1.115,0.635 10 false Certification ECU (Smart Key ECU Assembly) 1.417,4.604 1.573,4.781 0.156,0.177 10 false 9 1.604,4.719 1.969,4.896 0.365,0.177 10 false IG2D 0.417,5.51 0.979,5.688 0.563,0.177 10 false MAIN 0.521,6.167 1.604,6.344 1.083,0.177 10 false Auxiliary Battery 5.927,7.302 6.24,7.479 0.313,0.177 10 false D28 2.469,0.896 2.667,1.083 0.198,0.188 10 false 1A 2.49,1.344 2.688,1.531 0.198,0.188 10 false 1A 0.208,2.49 0.406,2.677 0.198,0.188 10 false 1C 0.979,2.49 1.177,2.677 0.198,0.188 10 false 1A 0.5,2.479 0.698,2.667 0.198,0.188 10 false 1 1.281,2.479 1.448,2.667 0.167,0.188 10 false 2 1.229,2.708 2.885,2.896 1.656,0.188 10 false No. 2 Integration Relay 3.813,1.115 4.979,1.49 1.167,0.375 10 false No. 1 Fuel Injector Assembly 3.781,2.365 4.927,2.76 1.146,0.396 10 false No. 2 Fuel Injector Assembly 3.781,3.625 4.938,4.052 1.156,0.427 10 false No. 3 Fuel Injector Assembly 3.792,4.885 4.979,5.302 1.188,0.417 10 false No. 4 Fuel Injector Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.
U110410E02
0.271,0.146 0.479,0.313 0.208,0.167 10 false *a 0.281,2.031 0.74,2.271 0.458,0.24 10 false D14 0.75,2.031 1.292,2.281 0.542,0.25 10 false D15 0.281,2.365 0.729,2.615 0.448,0.25 10 false D16 0.75,2.365 1.177,2.563 0.427,0.198 10 false D17

Disconnect the fuel injector assembly connectors.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D14-1 - Body ground Power switch on (IG) 11 to 14 V
D15-1 - Body ground Power switch on (IG) 11 to 14 V
D16-1 - Body ground Power switch on (IG) 11 to 14 V
D17-1 - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Fuel Injector Assembly)



OK

2.INSPECT FUEL INJECTOR ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - FUEL INJECTOR ASSEMBLY)
2.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL INJECTOR>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the fuel injector assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D14-2 - D28-85 (#10) Always Below 1 Ω
D15-2 - D28-84 (#20) Always Below 1 Ω
D16-2 - D28-83 (#30) Always Below 1 Ω
D17-2 - D28-82 (#40) Always Below 1 Ω
D14-2 or D28-85 (#10) - Body ground Always 10 Ω or higher
D15-2 or D28-84 (#20) - Body ground Always 10 Ω or higher
D16-2 or D28-83 (#30) - Body ground Always 10 Ω or higher
D17-2 or D28-82 (#40) - Body ground Always 10 Ω or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY (IG2 RELAY) - FUEL INJECTOR ASSEMBLY)
a.

Disconnect the fuel injector assembly connectors.


b.

Remove the No. 2 integration relay (IG2 relay) from the engine room relay block and junction block assembly.


c.

Disconnect the No. 2 integration relay connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D14-1 - 1A-4 Always Below 1 Ω
D15-1 - 1A-4 Always Below 1 Ω
D16-1 - 1A-4 Always Below 1 Ω
D17-1 - 1A-4 Always Below 1 Ω
D14-1 or 1A-4 - Body ground Always 10 kΩ or higher
D15-1 or 1A-4 - Body ground Always 10 kΩ or higher
D16-1 or 1A-4 - Body ground Always 10 kΩ or higher
D17-1 or 1A-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR