Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0ABF-123  Hybrid Battery Pack Current Sensor Circuit  P0AC1-123  Hybrid Battery Pack Current Sensor Circuit Low  P0AC2-123  Hybrid Battery Pack Current Sensor Circuit High  P0B10-123  Hybrid Battery Pack Current Sensor "B" Circuit Low  P0B11-123  Hybrid Battery Pack Current Sensor "B" Circuit High  


DESCRIPTION

A battery current sensor, which is mounted on the positive cable side of each hybrid battery junction block assembly, detects the current flowing to or from the battery pack. The battery current sensor sends a voltage, which varies between 0 and 5 V in proportion to the amperage, to the IB0 terminal of the battery smart unit. Similarly, it sends a voltage, which varies between 0 and 5 V in inverse proportion to the amperage, into the IB1 terminal of the battery smart unit. When the voltage of the IB0 terminal is below 2.8 V and the voltage of the IB1 terminal is above 2.2 V, this indicates that the HV battery is being discharged. Meanwhile, when the voltage of the IB0 terminal is above 2.8 V and the voltage of the IB1 terminal is below 2.2 V, this indicates that the HV battery is being charged. The battery smart unit sends the signals from its IB0 and IB1 terminals to the power management control ECU. The power management control ECU determines the charging and discharging amperage of the HV battery based on the received signals and calculates the SOC of the HV battery using the cumulative amperage value.

A230776E11
0.219,0.219 0.833,0.854 0.615,0.635 10 false Charging Current 1.156,0.219 1.938,0.854 0.781,0.635 10 false Discharging Current 1.823,2.938 3.042,3.333 1.219,0.396 10 false Battery Smart Unit 1.229,1.51 2.208,1.792 0.979,0.281 10 false Current sensor 2.219,1.792 2.5,1.99 0.281,0.198 10 false VIB 2.229,1.979 2.51,2.177 0.281,0.198 10 false IB0 2.229,2.156 2.51,2.354 0.281,0.198 10 false GIB 2.229,2.333 2.51,2.531 0.281,0.198 10 false IB1 3.854,0.115 6.323,0.448 2.469,0.333 10 false Battery Current Sensor Output Voltage 6.604,0.302 7.125,1.292 0.521,0.99 10 false Output Voltage (IB0) 3.698,0.75 3.958,0.948 0.26,0.198 10 false (V) 3.135,0.323 3.656,1.313 0.521,0.99 10 false Output Voltage (IB1) 6.292,0.74 6.552,0.938 0.26,0.198 10 false (V) 4.208,3.49 5.708,3.75 1.5,0.26 10 false HV Battery Current (A) 5.885,1.792 6.115,2.021 0.229,0.229 10 false IB1 5.146,2.5 5.375,2.729 0.229,0.229 10 false IB0 3.24,3.135 3.833,3.677 0.594,0.542 10 false Charging Current 6.365,3.167 7.146,3.76 0.781,0.594 10 false Discharging Current


DTC No. INF Code DTC Detection Condition Trouble Area
P0ABF
P0AC1
P0AC2
P0B10
P0B11
123 When the battery current sensor is abnormal (1 trip detection)
·

Hybrid battery junction block assembly

·

Battery smart unit

·

Wire harness or connector

·

HV battery



WIRING DIAGRAM

A398194E01
1.771,0.583 2.271,0.823 0.5,0.24 10 false IB0 1.781,1.219 2.281,1.458 0.5,0.24 10 false IB1 1.781,1.865 2.281,2.104 0.5,0.24 10 false VIB 1.76,2.5 2.26,2.74 0.5,0.24 10 false GIB 2.104,0.469 2.438,0.708 0.333,0.24 10 false 4 2.104,1.094 2.438,1.333 0.333,0.24 10 false 2 2.104,1.74 2.438,1.979 0.333,0.24 10 false 1 2.115,2.385 2.448,2.625 0.333,0.24 10 false 3 4.833,0.479 5.167,0.719 0.333,0.24 10 false 23 4.844,1.104 5.177,1.344 0.333,0.24 10 false 11 4.854,1.729 5.188,1.969 0.333,0.24 10 false 24 4.854,2.396 5.188,2.635 0.333,0.24 10 false 12 0.344,3.063 0.677,3.302 0.333,0.24 10 false z25 0.635,3.063 2.729,3.49 2.094,0.427 10 false Battery Current Sensor (Hybrid Battery Junction Block Assembly) 5.042,3.052 5.375,3.292 0.333,0.24 10 false z24 5.354,3.052 6.604,3.385 1.25,0.333 10 false Battery Smart Unit 5.125,0.594 5.625,0.833 0.5,0.24 10 false IB0 5.135,1.24 5.635,1.479 0.5,0.24 10 false IB1 5.125,1.854 5.625,2.094 0.5,0.24 10 false VIB 5.135,2.51 5.635,2.75 0.5,0.24 10 false GIB

Refer to the wiring diagram for DTC U0A29-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>U029A-123).


CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

If a short to +B occurs in the battery temperature sensor, battery current sensor or intake air temperature sensor, the following DTCs may be output simultaneously.


DTC No. Relevant Diagnosis
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High
P0AEB-123 Hybrid Battery Temperature Sensor "D" Circuit High
P0BC5-123 Hybrid Battery Temperature Sensor "E" Circuit High
P0C36-123 Hybrid Battery Temperature Sensor "F" Circuit High
P0AAF-123 Hybrid Battery Pack Air Temperature Sensor "A" Circuit High
P0AB4-123 Hybrid Battery Pack Air Temperature Sensor "B" Circuit High

PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.CHECK HARNESS AND CONNECTOR (B AND IGCT VOLTAGE)

B

2.CHECK HARNESS AND CONNECTOR (B AND IGCT VOLTAGE)

OK

3.CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY SMART UNIT POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

OK

4.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR HV BATTERY

4.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

OK

5.CHECK BATTERY SMART UNIT (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)

NG

5.CHECK BATTERY SMART UNIT (BATTERY CURRENT SENSOR OUTPUT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.
U190626E02
1.125,0.917 1.521,0.25 true 1.021,0.917 0.906,0.25 true 1.115,1.063 0.99,1.594 true 0.073,0.063 0.271,0.24 0.198,0.177 10 false *a 1.458,0.073 1.74,0.26 0.281,0.188 10 false IB1 0.74,0.073 1.073,0.281 0.333,0.208 10 false GIB 0.865,1.604 1.125,1.833 0.26,0.229 10 false IB0 0.333,0.865 0.615,1.01 0.281,0.146 10 false z24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z24-11 (IB1) - z24-12 (GIB) Power switch on (IG) 2.16 to 2.24 V
z24-23 (IB0) - z24-12 (GIB) Power switch on (IG) 2.76 to 2.84 V


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)


f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery shield sub-assembly.



OK

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY