Refer to the Description for DTC P0ABF-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0ABF-123).
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0AC0 | 123 | When the battery current sensor is abnormal (1 trip detection) | ·
Hybrid battery junction block assembly ·
Battery smart unit |
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read output DTCs.
| Result | Proceed to |
|---|---|
| P31AB-123 is not output | A |
| P31AB-123 is output | B |
Turn the power switch off.
A
B
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read output DTCs.
| Result | Proceed to |
|---|---|
| P301A-123 is not output | A |
| P301A-123 is output | B |
Turn the power switch off.
A
B
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Check that the shift lever is in P.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
When DTCs are cleared, freeze frame data and INF codes are also cleared.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List
Check "State of Charge (All Bat)" in the Data List.
Check that "State of Charge (All Bat)" is 60% or less.
If "State of Charge (All Bat)" is more than 60%, leave the hybrid system on with neutral (N) selected and reduce the SOC to 60% or less.
Apply the parking brake and secure the wheels using chocks.
Turn the power switch on (READY).
Depress the brake pedal with your left foot and move the shift lever to D. Repeat the following steps continuously for 1 minute or more.
Depress and release the accelerator pedal at intervals of 2.5 seconds continuously.
While depressing the brake pedal with your left foot, depress the accelerator pedal with your right foot.
Release the accelerator pedal.
Turn the power switch off.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read output DTCs.
| Result | Proceed to |
|---|---|
| DTCs P0AC0-123 is not output. | A |
| DTCs P0AC0-123 is output. | B |
Power switch off.
A
B