Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AC0-123  Hybrid Battery Pack Current Sensor Circuit Range / Performance  


DESCRIPTION

Refer to the Description for DTC P0ABF-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0ABF-123).

DTC No. INF Code DTC Detection Condition Trouble Area
P0AC0 123 When the battery current sensor is abnormal (1 trip detection)
·

Hybrid battery junction block assembly

·

Battery smart unit



CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read output DTCs.

Result:
Result Proceed to
P31AB-123 is not output A
P31AB-123 is output B



e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)

A

3.CHECK DTC OUTPUT (HYBRID CONTROL)

B

3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read output DTCs.

Result:
Result Proceed to
P301A-123 is not output A
P301A-123 is output B



e.

Turn the power switch off.



A

4.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

B

4.REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

5.CLEAR DTC (HYBRID CONTROL)
5.CLEAR DTC (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Check that the shift lever is in P.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Clear the DTCs and freeze frame data.

NOTICE:

When DTCs are cleared, freeze frame data and INF codes are also cleared.




NEXT

6.SIMULATION TEST
6.SIMULATION TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List


d.

Check "State of Charge (All Bat)" in the Data List.


e.

Check that "State of Charge (All Bat)" is 60% or less.

HINT:

If "State of Charge (All Bat)" is more than 60%, leave the hybrid system on with neutral (N) selected and reduce the SOC to 60% or less.



f.

Apply the parking brake and secure the wheels using chocks.


g.

Turn the power switch on (READY).


h.

Depress the brake pedal with your left foot and move the shift lever to D. Repeat the following steps continuously for 1 minute or more.

HINT:

Depress and release the accelerator pedal at intervals of 2.5 seconds continuously.

1.

While depressing the brake pedal with your left foot, depress the accelerator pedal with your right foot.

2.

Release the accelerator pedal.




i.

Turn the power switch off.



NEXT

7.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
7.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read output DTCs.

Result:
Result Proceed to
DTCs P0AC0-123 is not output. A
DTCs P0AC0-123 is output. B



e.

Power switch off.



A

RECOVERY TO NORMAL

B