The speed of the battery cooling blower assembly is controlled by the power management control ECU. Battery cooling blower assembly power is supplied when the FCTL terminal of the power management control ECU turns on the battery blower relay. The power management control ECU sends command signals (SI) to the battery cooling blower assembly to get the fan speed corresponding to the HV battery temperature. Information about the voltage applied to the battery cooling blower assembly (VM) is sent to the power management control ECU as a monitor signal using serial communication via the battery smart unit.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0A84 | 123 | When the output voltage of the battery cooling blower assembly (VM) is too low compared to the target control voltage range (1 trip detection) | ·
Wire harness or connector ·
No. 2 integration relay ·
Battery cooling blower assembly ·
Battery smart unit ·
Power management control ECU |
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
Select air volume mode 6 in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot be performed, skip it and proceed to the next step to check fan operates and air is sucked. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.
Change the air volume mode slowly. The battery cooling blower assembly speed will only increase in 1 mode steps, even if the air volume mode is rapidly changed from 1 to 6.
Check that the fan operates and air is sucked into the inlet duct.
The cooling fan may not stop even when turning the cooling fan off in the "Driving the Battery Cooling Fan" Active Test. This is due to HV system control and not a malfunction.
The fan operates.
Turn the power switch off.
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the front seat assembly RH (See Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
Turn over the front floor carpet.
Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).
Disconnect the S30 battery cooling blower assembly connector.
Disconnect the L144 battery smart unit connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-2 (VM0) - L144-8 (VM) | Power switch off | Below 1 Ω |
| S30-2 (VM0) or L144-8 (VM) - Body ground | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector
(to Battery Smart Unit) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S30-2 (VM0) - Body ground | Power switch on (IG) | Below 1 V |
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.
Check that each connector between the battery voltage sensor and battery cooling blower assembly is not loose or disconnected.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the L144 battery smart unit connector.
Reconnect the S30 battery cooling blower assembly connector.
Install the No. 1 hybrid battery shield sub-assembly.
Install the front floor carpet.
Install the front seat assembly RH.
OK
NG
Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
Turn over the front floor carpet.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
Enter the following menus: Powertrain / Hybrid Control / Data List / All Data / VMF Fan Motor Voltage 1.
Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling fan assembly.
While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency1) with the frequency value that was actually measured at the battery cooling blower assembly connector.
| Tester Connection | Condition |
|---|---|
| S30-2 (VM0) - S30-4 (GND0) | Battery cooling blower assembly is operating |
| *a | Component with harness connected
(Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector
(to Battery Cooling Blower Assembly) |
| Result | Proceed to |
|---|---|
| The value in the Data List (VMF Fan Motor Voltage 1) and the actual measurement value at the battery cooling blower assembly connector are below 1 V. | A |
| Other than above. | B |
Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.
Turn the power switch off.
Install the front floor carpet.
Install the front seat assembly RH.
A
B
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).
Disconnect the L144 battery smart unit connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
Select air volume mode 6 in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot be performed, skip it and proceed to the next step to check fan operates and air is sucked. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L144-8 (VM) - L144-4 (GND) | Battery cooling blower is operating | 1 V or more |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the L144 battery smart unit connector.
Install the No. 1 hybrid battery shield sub-assembly.
OK
NG
Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
Turn over the front floor carpet.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
Enter the following menus: All Data / VMF Fan Motor Voltage 1.
Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot be performed, skip it and proceed to the next step to check voltage. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.
While the cooling fan is operating, compare the value in the data list (VMF Fan Motor Voltage 1) with the voltage value that was actually measured at the battery cooling blower assembly connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-2 (VM0) - S30-4 (GND0) | Battery cooling blower is operating | Difference between the value in the Data List (VMF Fan Motor Voltage 1) and the actual measurement value is 1 V or less. |
| *a | Component with harness connected
(Battery Cooling Blower Assembly) |
| *b | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Compare the values in each air volume mode (1 to 6). If the active test cannot be performed, compare the values only in the current air volume mode.
Turn the power switch off.
Install the front floor carpet.
Install the front seat assembly RH.
OK
NG
Remove the BATT FAN fuse from the engine room relay block and junction block assembly
Measure the resistance of the BATT FAN fuse.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| BATT FAN fuse | Always | Below 1 Ω |
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | BATT FAN Fuse |
Install the BATT FAN fuse.
OK
NG
Remove the No. 2 integration relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *1 | No. 2 Integration Relay | *2 | BATT FAN Fuse |
| *3 | BATT FAN Relay | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1C-1 - 1A-8 | Battery voltage is applied across terminals 1A-6 and 1A-7 | Below 1 Ω |
| No battery voltage is applied across terminals 1A-6 and 1A-7 | 10 kΩ or higher |
Install the No. 2 integration relay.
OK
NG
Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
Turn over the front floor carpet.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-1 (IG0) - S30-4 (GND0) | Power switch on (IG) | 11 to 14 V |
| *a | Component with harness connected
(Battery Cooling Blower Assembly) |
| *b | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the voltage on the wire side of the connector that is part of the battery cooling blower.
Turn the power switch off.
Install the front floor carpet.
Install the front seat assembly RH.
OK
NG
Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
Turn over the front floor carpet.
Disconnect the S30 battery cooling blower assembly connector.
Disconnect the A21 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-3 (SI0) - A21-29 (SI0) | Power switch off | Below 1 Ω |
| S30-3 (SI0) or A21-29 (SI0) - Body ground | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector
(to Power Management Control ECU) |
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-3 (SI0) - Body ground | Power switch on (IG) | Below 1 V |
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
Turn the power switch off.
Reconnect the A21 power management control ECU connector.
Reconnect the S30 battery cooling blower assembly connector.
Install the front floor carpet.
Install the front seat assembly RH.
OK
NG
Remove the power management control ECU (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>COMPONENTS).
| *a | Component without harness connected
(Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
|---|---|
| A21-29 (SI0) - L5-5 (E01) | 10 kΩ or higher |
Install the power management control ECU.
OK
NG
Turn the power switch on (IG).
| *a | Component with harness connected
(Power Management Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A21-29 (SI0) - L5-5 (E01) | Power switch on (IG) | 4.5 to 5.5 V |
Turn the power switch off.
OK
NG
Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
Turn over the front floor carpet.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot be performed, skip it and proceed to the next step to check fan operates and air is sucked. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.
Connect an oscilloscope to the S30 battery cooling blower assembly connector and check the waveform.
| Item | Content |
|---|---|
| Tester Connection | S30-3 (SI0) - S30-4 (GND0) |
| Equipment Setting | 10 V/DIV., 1 ms/DIV. |
| Condition | Power switch on (IG) during Active Test |
| *a | Component with harness connected
(Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector
(to Battery Cooling Blower Assembly) |
Perform this inspection with the battery cooling blower assembly connector connected.
If DTCs are output after the check, clear the DTCs using the GTS.
Turn the power switch off.
Install the front floor carpet.
Install the front seat assembly RH.
| *a | Waveform 1 |
| Result | Proceed to |
|---|---|
| Normal (The pulse output of waveform 1) | A |
| No pulse generation | B |
A
B
Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
| *a | Component with harness connected
(Battery Cooling Blower Assembly) |
| *b | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-4 (GND0) - Body ground | Power switch off | Below 1 Ω |
Install the front seat assembly RH.
OK
NG
Disconnect the A21 power management control ECU connector.
Remove the No. 2 integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1A-7 - A21-4 (FCTL) | Power switch off | Below 1 Ω |
| *a | Front view of wire harness connector
(to No. 2 Integration Relay) |
| *b | Rear view of wire harness connector
(to Power Management Control ECU) |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A21-4 (FCTL) - Body ground | Power switch off | Below 1 V |
| Power switch on (IG) | Below 1 V |
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
Turn the power switch off.
Reconnect the A21 power management control ECU connector.
Install the No. 2 integration relay.
OK
NG
Disconnect the L5 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L5-5 (E01) - Body ground | Power switch off | Below 1 Ω |
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the L5 power management control ECU connector.
OK
NG
Disconnect the L6 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L6-5 (E02) - Body ground | Power switch off | Below 1 Ω |
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the L6 power management control ECU connector.
OK
NG
Remove the No. 2 integration relay.
Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
Turn over the front floor carpet.
Disconnect the S30 battery cooling blower assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1A-8 - S30-1 (IG0) | Power switch off | Below 1 Ω |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Integration Relay) |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the S30 battery cooling blower assembly connector.
Install the front floor carpet.
Install the front seat assembly RH.
Install the No. 2 integration relay.
OK
NG
Remove the No. 2 integration relay.
Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
Turn over the front floor carpet.
Disconnect the S30 battery cooling blower assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-1 (IG0) - Terminals other than 1A-8 and body ground | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Integration Relay) |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the S30 battery cooling blower assembly connector.
Install the front floor carpet.
Install the front seat assembly RH.
Install the No. 2 integration relay.
OK
NG
Remove the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL).
Turn over the front floor carpet.
Disconnect the S30 battery cooling blower assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-1(IG0) - S30-4(GND0) and body ground | Power switch off | 10 kΩ or higher |
| *a | Component without harness connected
(Battery Cooling Blower Assembly) |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the S30 battery cooling blower assembly connector.
Install the front floor carpet.
Install the front seat assembly RH.
OK
NG
NEXT
NEXT