Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301581 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  INSTALLATION  


PROCEDURE

Hide 82164 1.INSTALL FRAME WIRE

CAUTION:

Wear insulated gloves.


a.

Install the frame wire with 3 new clamps.


b.
A251309E02
2.885,0.698 3.063,1.01 0.177,0.313 10 false *a

Insert the frame wire into the floor panel hole.

Text in Illustration
*a Front of Vehicle

HINT:

The arrow should be pointing toward the front of the vehicle.



c.

Install the 3 nuts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


d.

Install the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


e.

Install the nut and clamp.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


f.

Install the nut and 2 clamps.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


g.

Install the heater water pipe sub-assembly with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


h.

Connect the 4 clamps.


i.

Connect the connector to the engine room junction block assembly.


j.

Engage the 3 claws.


k.

Connect the 4 wire harness clamps to the floor panel.


l.

Connect the clamp to the floor panel to install the wire harness protector.


m.

Install the floor carpet with the 2 clips.


Hide G92Z0 2.CONNECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:

Wear insulated gloves.


a.

Install the frame wire on the hybrid battery junction block assembly with the 3 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

Make sure that the ends of the frame wire are not crossed over each other.

·

Be sure to connect the ends of the frame wire to the connect terminals.




Hide 3.CONNECT CABLE TO POSITIVE AUXILIARY BATTERY TERMINAL

a.

Connect the 4 clamps.


b.

Install the nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Install the terminal cover.


Hide 64730B 4.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).


Hide 64712F 6.INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).


Hide 58460D 7.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).


Hide 64721G 8.INSTALL NO. 1 DECK TRIM COVER (for RH Side)

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).


Hide 73560 9.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

Hide 73360C 10.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

Hide 12.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 13.INSTALL REAR NO. 1 SEAT ASSEMBLY (for Center)

Hide 14.INSTALL REAR NO. 1 SEAT ASSEMBLY (for Side)

Hide 64910J 15.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 52257 16.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

a.

Using a transmission jack, hold the front suspension cross member.

NOTICE:

Be sure to position the transmission jack to properly support the front suspension cross member.



b.
A248480E06
1.594,1.219 1.76,1.375 0.167,0.156 10 true A 2.615,1.677 2.781,1.833 0.167,0.156 10 true B 0.802,1.406 0.969,1.563 0.167,0.156 10 true B

Remove the bolt A


c.

Install the front suspension member rear brace RH with the 2 bolts B and bolt A.

Torque:
Bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
Bolt B : 93 N*m (948 kgf*cm, 69 ft.*lbf)


Hide 58151 17.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the No. 1 front floor heat insulator with the 3 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 18.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide G9200 19.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide G920Q 20.INSTALL NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide 58817A 22.INSTALL FRONT NO. 2 CONSOLE BOX INSERT

Hide 58804A 23.INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY