55303B
1.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)
When using a new lower instrument panel sub-assembly:
Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portion shown in the illustration.
Install the lower instrument panel sub-assembly with the 2 bolts <A>, 10 screws <C> and screw <D>.
Engage the 2 claws.
Engage the 2 claws to connect the room temperature sensor.
Engage each clamp.
Connect the connector and engage the claw as shown in the illustration.
Be sure to engage the connector securely.
Connect the connector.
55303B
2.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
When using a new lower instrument panel sub-assembly:
Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portion shown in the illustration.
Install the lower instrument panel sub-assembly with the 2 bolts <A>, 10 screws <C> and screw <D>.
Engage the 2 claws to connect the DLC3.
Engage the 2 claws to connect the room temperature sensor.
Engage each clamp.
86101
3.INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)
86101
4.INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)
81260
5.INSTALL GLOVE BOX LIGHT ASSEMBLY
53601
6.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
73900
7.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
55606
8.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Connect each connector.
Engage each clamp.
Engage the guide and 2 claws.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <E>.
62112A
9.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
67914
10.INSTALL FRONT DOOR SCUFF PLATE LH
33560
11.INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY
55900
12.INSTALL AIR CONDITIONING CONTROL ASSEMBLY
13.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Connect each connector.
Engage the clamp.
Engage the 11 claws to install the lower instrument finish panel sub-assembly.
14.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)
15.INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type)
16.INSTALL COMBINATION METER ASSEMBLY
Connect each connector.
Engage the clamp.
Install the combination meter assembly with the 4 screws <E>.
58810J
17.INSTALL CONSOLE BOX ASSEMBLY
58817A
18.INSTALL FRONT NO. 2 CONSOLE BOX INSERT
58804A
19.INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
58821C
20.INSTALL UPPER CONSOLE PANEL
58534H
21.INSTALL CENTER FLOOR CARPET COVER LH
Engage the guide and 4 claws to install the center floor carpet cover LH as shown in the illustration.
58533F
22.INSTALL CENTER FLOOR CARPET COVER RH
Engage the guide and 4 claws to install the center floor carpet cover RH as shown in the illustration.
55054
23.INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
Engage the claw to install the glove compartment door stopper sub-assembly.
55550
24.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
With the glove compartment door assembly opened approximately 65° from its closed position, engage the 2 hinges horizontally.
Make sure to check that the hinge is engaged securely. If it is not, the glove compartment door assembly may not open/close properly and the lock portion may be damaged.
| *a | Opened Approximately 65° |
| *b | Closed |
Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.
| *1 | Glove Compartment Door Stopper Sub-assembly |
| *2 | Stopper |
Engage the claw and connect the glove compartment door stopper sub-assembly.
55607
25.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Connect the connector.
Engage the guide and 3 claws to install the No. 2 instrument panel under cover sub-assembly.
62111C
26.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION)
67913
27.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION)
28.INSTALL UPPER INSTRUMENT PANEL ASSEMBLY
29.INSPECT SHIFT LEVER OPERATION