1.INSPECT COOLANT (for Engine)
2.INSPECT ENGINE OIL
3.INSPECT AUXILIARY BATTERY
17801
4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner cap.
Remove the air cleaner filter element.
Visually check that the air cleaner filter element is not excessively damaged or oily.
If necessary, replace the air cleaner filter element.
Install the air cleaner filter element.
Install the air cleaner cap.
5.INSPECT VALVE AND ADJUSTER NOISE
Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Rev up the engine several times. Check that the engine does not emit unusual noises. If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then, perform the inspection above again. If any defects or problems are found during the inspection above, perform a lash adjuster inspection (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).
6.INSPECT IGNITION TIMING
Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Warm up and stop the engine.
When using the GTS:
Check the ignition timing.
Connect the GTS to the DLC3.
Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
0 to 16 degrees BTDC
Check the ignition timing with the cooling fans off.
Turn off all electrical systems and the A/C.
When checking the ignition timing, the shift position park (P) should be selected.
Refer to the GTS operator's manual for further details.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.
Monitor IGN Advance of the Data List.
8 to 12 degrees BTDC
When checking the ignition timing, the shift position park (P) should be selected.
Refer to the GTS operator's manual for further details.
Enter the following menus: Connect the TC and TE1 / OFF.
Turn the power switch off.
Turn the GTS off.
Disconnect the GTS from the DLC3.
When not using the GTS:
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *1 | DLC3 |
Confirm the terminals before connecting them. Connecting the wrong terminals may result in damage to electrical components.
Check the ignition timing with the cooling fans off.
Turn off all electrical systems and the A/C.
When checking the ignition timing, the shift position park (P) should be selected.
Remove the No. 2 cylinder head cover.
Pull out the wire harness.
After checking, wrap the wire harness with tape.
Connect the clip of the timing light to the wire harness.
Use a timing light that detects the primary signal.
Inspect the ignition timing at idle.
8 to 12 degrees BTDC
When checking the ignition timing, the shift position park (P) should be selected.
After running the engine at 1000 to 1300 rpm for 5 seconds, check that it returns to idle speed.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing at idle.
0 to 16 degrees BTDC
Confirm that the ignition timing advances when the engine rpm is increased.
Remove the timing light.
Install the No. 2 cylinder head cover.
7.INSPECT ENGINE IDLE SPEED
Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Warm up and stop the engine.
When using the GTS:
Connect the GTS to the DLC3.
Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Refer to the GTS operator's manual for further details.
Inspect the engine idle speed.
950 to 1050 rpm
Turn all electrical systems and the A/C off.
Inspect the idle speed with the cooling fans off.
When checking the idle speed, the shift position park (P) should be selected.
Turn the power switch off.
Turn the GTS off.
Disconnect the GTS from the DLC3.
When not using the GTS:
Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.
| *1 | DLC3 |
Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Inspect the engine idle speed.
950 to 1050 rpm
Turn all electrical systems and the A/C off.
Inspect the idle speed with the cooling fans off.
When checking the idle speed, the shift position park (P) should be selected.
Disconnect terminal 9 (TAC) of the DLC3.
8.INSPECT COMPRESSION
Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Warm up and stop the engine.
Remove the 4 spark plugs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL).
If the ignition coil assembly connector is disconnected because a DTC is detected in inspection, always reconnect it.
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Check the HV battery voltage in the data list to ensure that the battery is fully charged.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Compression Test / ON.
Depress and hold the brake pedal, and turn the power switch on (READY).
The measurement must be done as quickly as possible.
Noise may be emitted from the transmission. However, this is not a malfunction.
Always use a fully charged auxiliary battery to obtain an engine speed of 200 rpm or more.
813 kPa (8.3 kgf/cm2, 118 psi)
617 kPa (6.3 kgf/cm2, 89.5 psi)
100 kPa (1.0 kgf/cm2, 14.5 psi)
Inspect the other cylinders in the same way.
Measure the compression as quickly as possible.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole, then inspect it again.
If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
If the pressure stays low, a valve may be stuck or seated improperly, or there may be leaks from the gasket.
Install the 4 spark plugs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION).
After performing all the procedures, be sure to clear any DTCs stored in memory.
9.INSPECT CO/HC
This check determines whether or not the idle CO / HC complies with regulations.
Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Warm up the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.
Check the CO/HC concentration while idling and when the engine is running at 2500 rpm.
When doing a 2 mode (with the engine idling/ running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.
If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
Check the DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problem | Possible Cause |
|---|---|---|---|
| Normal | High | Rough idle | 1.
Faulty ignition: -
Incorrect timing -
Fouled, shorted or improperly gapped plugs 2.
Incorrect valve clearance 3.
Leaks from intake and exhaust valves 4.
Leaks from cylinders 5.
Faulty EGR |
| Low | High | Rough idle (Fluctuating HC reading) | 1.
Vacuum leaks: -
PCV hoses -
Intake manifold -
Throttle body 2.
Lean mixture causing misfire 3.
Faulty EGR |
| High | High | Rough idle (Black smoke from exhaust) | 1.
Restricted air cleaner filter element 2.
Plugged PCV valve 3.
Faulty EFI systems: -
Faulty pressure regulator -
Faulty engine coolant temperature sensor -
Faulty mass air flow meter -
Faulty ECM -
Faulty injectors -
Throttle body 4.
Faulty EGR |