Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301595 CYLINDER HEAD GASKET A

2ZR-FXE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11115 5.INSTALL CYLINDER HEAD GASKET

a.
A215254E21
0.208,0.917 0.208,0.708 0.208,0.708 0.531,0.479 false 0.854,0.646 1.031,0.813 0.177,0.167 10 false *1 1.073,0.063 3.01,0.24 1.938,0.177 10 false 2 to 4 mm (0.0787 to 0.157 in.) 0.021,0.917 0.656,1.125 0.635,0.208 10 false 4 mm 0.281,1.198 1.458,1.604 1.177,0.406 10 false 10 to 15 mm (0.394 to 0.591 in.) 0.24,2.375 1.406,2.76 1.167,0.385 10 false 10 to 15 mm (0.394 to 0.591 in.)

Apply seal packing (diameter 4.0 mm (0.157 in.)) to the cylinder block as shown in the illustration.

Text in Illustration
*1 Cylinder Block
V100135

Engine Front

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:

Remove any oil from the cylinder block.



b.
A221760E02
1.97,0.157 2.121,0.308 0.151,0.151 10 *a 1.464,0.494 1.649,0.248 1.649,0.248 1.954,0.248 false

Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.

Text in Illustration
*a Lot No.
V100135

Engine Front

NOTICE:

Install the cylinder head gasket within 3 minutes of applying seal packing.



c.
A233569E10
0.427,0.875 0.427,0.781 0.427,0.781 0.719,0.5 false 1.677,0.552 1.552,0.552 1.552,0.552 1.344,0.615 false 1.646,2.583 1.448,2.417 false 1.677,1.01 0.802,1.188 0.802,1.188 0.802,1.323 false 1.719,0.479 1.885,0.635 0.167,0.156 10 false *1 1.302,0.094 2.979,0.271 1.677,0.177 10 false 0 to 2 mm (0 to 0.0787 in.) 0.271,0.896 0.667,1.042 0.396,0.146 10 false 4 mm 0.302,1.333 1.479,1.729 1.177,0.396 10 false 10 to 15 mm (0.394 to 0.591 in.) 0.281,2.302 1.448,2.719 1.167,0.417 10 false 10 to 15 mm (0.394 to 0.591 in.)

Apply seal packing (diameter 4.0 mm (0.157 in.)) to the new cylinder head gasket as shown in the illustration.

Text in Illustration
*1 Cylinder Head Gasket
V100135

Engine Front

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the cylinder head gasket and cylinder head.

·

Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.




d.
A214976E02
0.893,2.009 1.056,2.193 0.162,0.184 10 *a 2.508,2.009 2.691,2.177 0.183,0.168 10 *b

After tightening the cylinder head bolts, wipe off any seal packing material that seeped out from the contact surfaces between the cylinder head and cylinder block.

Text in Illustration
*a Before wiping off
*b After wiping off


Hide 11101 6.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head bolts are tightened in 3 progressive steps.


a.

Place the cylinder head on the cylinder block.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head.

·

Place the cylinder head on the cylinder block gently in order not to damage the gasket with the bottom part of the head.




b.

Install the plate washers to the cylinder head bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


d.
A150891E16
0.583,0.099 0.691,0.25 0.108,0.152 10 8 1.122,0.099 1.229,0.25 0.108,0.152 10 4 1.668,0.113 1.775,0.264 0.108,0.152 10 2 2.2,0.113 2.308,0.264 0.108,0.152 10 5 2.768,0.092 2.875,0.244 0.108,0.152 10 9 1.647,1.78 1.761,1.935 0.114,0.155 10 1 1.095,1.782 1.202,1.933 0.108,0.152 10 6 0.506,1.782 0.697,1.933 0.191,0.152 10 10 2.225,1.782 2.333,1.933 0.108,0.152 10 3 2.775,1.782 2.883,1.933 0.108,0.152 10 7

Step 1:

i.

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps, in the sequence shown in the illustration.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Do not drop the plate washers into the cylinder head.




e.
A156439E06
2.562,0.017 2.890,0.163 0.327,0.147 10 45° 1.308,0.298 1.635,0.444 0.327,0.147 10 90° 1.944,1.077 1.477,1.544 false 1.366,1.563 1.550,1.728 0.184,0.165 10 *a

Step 2:

Text in Illustration
*a Paint Mark
V100136

Engine Front

i.

Mark each cylinder head bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head bolts 90° in the sequence shown in step 1.



f.

Step 3:

i.

Tighten the cylinder head bolts another 45° in the sequence shown in step 1.



g.

Check that the paint mark is now at a 135° angle to the front.


Hide 13801 9.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 17167 11.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11103 12.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY