Home › Engine / Hybrid System › 2ZR-FXE (EMISSION CONTROL) › EGR VALVE
RM2070E _51 Engine / Hybrid System _061909 2ZR-FXE EMISSION CONTROL _0301609 EGR VALVE A

2ZR-FXE EMISSION CONTROL  EGR VALVE  INSTALLATION  


PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25620 2.INSTALL EGR VALVE ASSEMBLY

a.
A297470

Temporarily install a new gasket and EGR valve assembly to the EGR cooler assembly with the 2 nuts.


b.

Install a new gasket and set the EGR valve with cooler assembly in place.


c.

Using an E8 "TORX" socket wrench, install the 4 stud bolts.

A297489E01
2.207,1.569 2.363,1.750 0.156,0.181 10 *a 1.157,2.229 1.313,2.410 0.156,0.181 10 *a 3.935,1.762 4.091,1.944 0.156,0.181 10 *b 3.46,2.639 3.616,2.820 0.156,0.181 10 *b 4.88,1.459 5.036,1.640 0.156,0.181 10 *c 5.787,2.632 5.943,2.813 0.156,0.181 10 *c 4.698,0.405 4.853,0.586 0.156,0.181 10 *c 0.346,2.908 0.853,3.061 0.508,0.154 10 73 mm 0.346,3.064 0.930,3.252 0.584,0.188 10 (2.87 in.) 2.544,3.132 3.039,3.306 0.495,0.174 10 25 mm 2.544,3.29 3.230,3.471 0.686,0.180 10 (0.984 in.) 4.981,3.104 5.486,3.277 0.505,0.173 10 29 mm 4.981,3.261 5.593,3.460 0.612,0.199 10 (1.14 in.) 1.616,2.529 2.163,2.696 0.547,0.166 10 20 mm 1.616,2.68 2.340,2.872 0.724,0.192 10 (0.787 in.) 1.616,3.314 2.146,3.478 0.530,0.164 10 13 mm 1.616,3.461 2.319,3.656 0.703,0.195 10 (0.512 in.) 3.904,3.122 4.611,3.311 0.707,0.188 10 (0.787 in.) 3.904,2.965 4.555,3.138 0.651,0.173 10 20 mm 3.904,3.3 4.403,3.470 0.498,0.170 10 13 mm 3.904,3.457 4.627,3.654 0.723,0.196 10 (0.512 in.) 6.234,3.1 6.925,3.276 0.691,0.176 10 (0.551 in.) 6.234,2.951 6.721,3.116 0.488,0.165 10 14 mm 6.234,3.332 6.689,3.492 0.455,0.161 10 13 mm 6.234,3.476 6.937,3.651 0.704,0.175 10 (0.512 in.)

Text in Illustration
*a Stud Bolt A *b Stud Bolt B
*c Stud Bolt C - -

Torque:
Stud Bolt A and Stud Bolt B : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Stud Bolt C : 5.0 N*m (51 kgf*cm, 44 in.*lbf)

If a stud bolt is deformed or the threads are damaged, replace it.


d.

Temporarily install the 2 nuts (B), 2 nuts (C) and bolt.

HINT:

The type B nut and type C nut are non-reusable.

A307474E02
0.328,1.913 0.484,2.094 0.156,0.181 10 *b 1.962,2.128 2.118,2.309 0.156,0.181 10 *b 1.212,1.839 1.368,2.020 0.156,0.181 10 *a 2.645,0.723 2.801,0.904 0.156,0.181 10 *c 3.962,0.786 4.263,1.113 0.302,0.327 12 *A 4.844,0.786 5.146,1.113 0.302,0.327 12 *B 5.944,0.786 6.246,1.113 0.302,0.327 12 *C 2.906,1.831 3.062,2.013 0.156,0.181 10 *c 0.905,0.6 1.061,0.781 0.156,0.181 10 *a 1.506,0.486 1.662,0.667 0.156,0.181 10 *d 4.999,1.873 5.711,2.233 0.711,0.360 10 18 mm (0.709 in.) 6.117,1.873 6.828,2.233 0.711,0.360 10 17 mm (0.669 in.) 3.906,0.738 4.724,2.261 0.817,1.522 4.794,0.738 5.784,2.261 0.99,1.522 5.905,0.738 6.905,2.261 0.999,1.522

Text in Illustration
*A Type A *B Type B
*C Type C - -
*a Nut A *b Nut B
*c Nut C *d Bolt



e.

Tighten the 2 nuts (A).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.

Tighten the 2 nuts (B) and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Make sure that all installation surfaces of the EGR valve with cooler assembly are in even contact when tightening the bolt and nuts.



g.

Tighten the 2 nuts (C).

Torque:
Type A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Type B : 37 N*m (377 kgf*cm, 27 ft.*lbf)
Type C : 26 N*m (265 kgf*cm, 19 ft.*lbf)


h.
A212666

Connect the EGR valve assembly connector and engage the wire harness clamp.


i.

Connect the 4 water hoses to the EGR valve assembly and slide the 4 clips to secure them.


Hide 25610 3.INSTALL EGR PIPE ASSEMBLY

a.

Install 2 new gaskets and EGR pipe assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Make sure to tighten the 4 bolts evenly until the flanges of the EGR pipe assembly contact the installation surfaces.



b.

Install the wire harness support with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A212663

Connect the 2 wire harness clamps.


Hide 55701J 10.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 11.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55736D 12.INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)

Hide 55735C 13.INSTALL COWL BODY MOUNTING REINFORCEMENT RH (for RHD)

Hide 14.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY