Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301598 ENGINE ASSEMBLY A

2ZR-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 13405 1.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Gently place the engine assembly onto wood blocks or equivalent.

NOTICE:

This step should be done while hanging the engine assembly using the engine hangers and a chain block.




Hide 31270 2.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

a.

Gently place the engine assembly onto wood blocks or equivalent.

NOTICE:

This step should be done while hanging the engine assembly using the engine hangers and a chain block.



b.

Install the transmission input damper assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>INSTALLATION).


Hide 30900 3.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.

Install the hybrid vehicle transaxle assembly (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>INSTALLATION).

NOTICE:

Be careful not to apply excess force to the transmission input damper assembly when removing or installing the hybrid vehicle transaxle assembly. If excess force is applied, the transmission input damper assembly may be damaged, or its splines may become misaligned.



Hide 82121 4.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine.


Hide 16577C 7.INSTALL RADIATOR PIPE

a.

Install the radiator pipe with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Install the No. 3 radiator hose with the clamp.


Hide 12305 8.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.


a.
A281978E03
0.979,3.177 1.115,3.333 0.135,0.156 10 false A 0.979,3.177 1.115,3.333 0.135,0.156 10 false A 3.135,1.417 3.271,1.573 0.135,0.156 10 true B 2.135,0.313 2.271,0.469 0.135,0.156 10 true C

Position the engine mounting insulator sub-assembly RH as shown in the illustration.


b.

Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.


c.

Tighten the 3 bolts to install the engine mounting insulator sub-assembly RH in the order of the bolt B, bolt C and bolt A.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


d.

Connect the earth wire clamp to the engine mounting insulator sub-assembly RH.


e.

Install the 2 cooler brackets with the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 12372A 9.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.


a.
A215740E03
1.802,1.188 1.938,1.344 0.135,0.156 10 true A 1.833,1.813 1.969,1.969 0.135,0.156 10 true B 0.323,0.573 0.458,0.729 0.135,0.156 10 true C 0.615,1.229 0.75,1.385 0.135,0.156 10 true D

Temporarily install the engine mounting insulator LH with the 4 bolts.


b.

Tighten the 4 bolts to install the engine mounting insulator LH in the order of the bolt C, bolt B, bolt D and bolt A.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 12371A 10.INSTALL REAR ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator to the engine mounting bracket with the through bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.



Hide 12361A 11.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.
A219120

Temporarily install the front engine mounting insulator with the bolt and nut.

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.



Hide 12.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on the engine lifter.

NOTICE:
·

Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.

·

Do not position a height adjustment attachment or plate lift attachment onto the front cross member sub-assembly.



HINT:

Place the engine on wooden blocks or equivalent so that the engine is level.



b.

Remove the 2 bolts and 2 engine hangers.


c.

Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulators RH and LH can be installed.

CAUTION:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While raising the engine into the vehicle, do not allow it to contact the vehicle.




d.

Install the front crossmember with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


e.
A282375

Install the front engine mounting insulator to the front crossmember with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.



f.

Install the engine mounting insulator LH with the through bolt and nut.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

NOTICE:

When installing the engine mounting insulator, tighten the nut while holding the bolt.



g.
A158372E01
1.188,0.402 1.300,0.544 0.112,0.142 10 A 2.39,1.575 2.502,1.717 0.112,0.142 10 B

Install the engine mounting insulator RH with the bolt and 2 nuts.

Torque:
Nut A : 95 N*m (969 kgf*cm, 70 ft.*lbf)
Nut B : 52 N*m (530 kgf*cm, 38 ft.*lbf)
Bolt : 95 N*m (969 kgf*cm, 70 ft.*lbf)


h.

Tighten the front engine mounting insulator with the bolt and nut.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)


Hide 51201 13.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 52258A 14.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH

Hide 52257 15.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Perform the same procedure as for the LH side.


Hide 51108A 16.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 17.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

Hide 51425A 18.INSTALL FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT

Hide 43040B 19.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43030B 20.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH

HINT:

Perform the same procedure as for the LH side.


Hide 43410 22.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 23.INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 24.INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 25.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 26.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 27.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 28.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89543 29.INSTALL FRONT SPEED SENSOR LH

Hide 89542 30.INSTALL FRONT SPEED SENSOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 43501H 32.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 17410 33.INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ Exhaust Heat Recirculation System)

Hide 17410 34.INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o Exhaust Heat Recirculation System)

Hide 45025D 37.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 38.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)

Hide 45259A 39.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 82121 40.CONNECT ENGINE WIRE

a.

Connect the engine wire with the 2 clamps.


b.

Install the earth wire with the bolt.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


c.

Connect the wire harness with the 3 clamps.


d.
A241115

Connect the wire harness to the engine room junction block.


e.

Connect the 2 connectors and 2 clamps to the engine room junction block.


f.
A218642

Connect the connector to the ECM with the lock lever.


g.

Connect the 2 clamps.


Hide 88370 41.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

Hide 23901 42.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube connector and fuel pipe.

CAUTION:

Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a "click" sound. If the connection is tight, apply a small amount of engine oil to the tip of the pipe. After connecting, pull the pipe and connector to make sure that they are securely connected.



b.

Install the No. 1 fuel pipe clamp.


Hide 23826 43.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose with the clamp.


Hide 44.CONNECT HEATER HOSE

a.

Connect the heater hose with the clamp.


Hide 87245A 45.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose with the clamp.


Hide 87246A 46.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose with the clamp.


Hide G9229A 47.CONNECT NO. 5 INVERTER COOLING HOSE

a.

Connect the No. 5 inverter cooling hose with the clamp.


Hide G9227A 48.CONNECT NO. 3 INVERTER COOLING HOSE

a.

Connect the No. 3 inverter cooling hose with the clamp.


Hide 16281 49.CONNECT NO. 4 WATER BY-PASS HOSE

a.

Connect the No. 4 water by-pass hose with the clamp.


Hide 16572D 50.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose with the clamp.


Hide 16571C 51.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose with the clamp.


Hide G9219A 52.INSTALL INVERTER TRAY BRACKET

a.
A213025E04
2.396,0.99 2.51,1.146 0.115,0.156 10 true A 2,0.135 2.146,0.302 0.146,0.167 10 true B 2.375,1.833 2.51,2 0.135,0.167 10 true C 1.531,1.708 1.656,1.885 0.125,0.177 10 true D 1.531,1.229 1.667,1.396 0.135,0.167 10 true E

Position the inverter tray bracket as shown in the illustration.


b.

Temporarily install the inverter tray bracket with the 5 bolts.


c.

Tighten the 5 bolts to install the inverter tray bracket in the order of the bolt A, bolt C, bolt D, bolt E and bolt B.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.

Connect the 2 clamps to the inverter tray bracket.


Hide G92A0A 53.INSTALL INVERTER RESERVE TANK ASSEMBLY

a.
A213024E03
1.333,1.854 1.448,2.021 0.115,0.167 10 true A 2.729,1.271 2.885,1.448 0.156,0.177 10 true B

Temporarily install the inverter reserve tank assembly with the 2 bolts.


b.

Tighten the 2 bolts to install the inverter reserve tank assembly in the order of the bolt B and bolt A.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 67.INSTALL AIR CLEANER CASE

a.
A213023

Install the air cleaner case with the 3 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the No. 4 water by-pass hose to the air cleaner case with the 3 clamps.


c.

Install the air cleaner filter element.


Hide 17750A 68.INSTALL INLET AIR CLEANER ASSEMBLY

a.

Install the inlet air cleaner assembly with the 3 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the No. 4 water by-pass hose to the inlet air cleaner assembly with the clamp.


Hide 17705 69.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

a.

Install the air cleaner filter element.


b.

Install the air cleaner cap sub-assembly with the 2 clamps and hose band.


c.

Connect the air flow meter connector.


Hide 80.INSPECT FOR OIL LEAK

Hide 81.INSPECT FOR EXHAUST GAS LEAK

Hide 51442E 82.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 83.INSTALL NO. 1 ENGINE UNDER COVER

Hide 52618A 84.INSTALL FRONT LOWER BUMPER ABSORBER

Hide 51444A 85.INSTALL REAR ENGINE UNDER COVER LH

Hide 51443C 86.INSTALL REAR ENGINE UNDER COVER RH

Hide 87.INSTALL FRONT WHEELS

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 88.CHECK FRONT WHEELS FACING STRAIGHT AHEAD

Hide 92.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 53289A 93.INSTALL RADIATOR SUPPORT OPENING COVER

Hide 11212 94.INSTALL NO. 2 CYLINDER HEAD COVER

a.

Engage the 3 clips to install the cover.

NOTICE:
·

Be sure to engage the clips securely.

·

Do not apply excessive force or hit the cover to engage the clips. This may cause the cover to break.