Home › Engine / Hybrid System › 2ZR-FXE (COOLING) › EXHAUST HEAT RECIRCULATION SYSTEM › 2014.11–2020.08
RM2070E _51 Engine / Hybrid System _061911 2ZR-FXE COOLING _0301622 EXHAUST HEAT RECIRCULATION SYSTEM J

2ZR-FXE COOLING  EXHAUST HEAT RECIRCULATION SYSTEM  Exhaust Heat Recirculation System Circuit  


DESCRIPTION

In the exhaust heat recirculation system, coolant is warmed up using exhaust gas heat to accelerate engine warm-up time, enhancing fuel efficiency and heater performance.

The heat recirculator is positioned in the front exhaust pipe assembly after the catalyst. Coolant from the engine flows around the heat recirculator and then returns to the engine. If the engine is started while the engine is cold, the exhaust pipe gas control actuator sub-assembly rod is contracted and the exhaust flow control valve is closed, routing the exhaust gas around the heat recirculator to warm up the coolant.

After the engine coolant temperature rises and the engine has warmed up, the heat of the coolant expands the thermostat and the exhaust pipe gas control actuator sub-assembly rod extends. This opens the exhaust flow control valve to switch to the normal exhaust gas path.

The exhaust flow control valve can also be opened by exhaust gas pressure to prevent insufficient acceleration performance when the engine is cold. In addition, to monitor the engine coolant temperature, an engine coolant temperature sensor (for exhaust heat recirculation system) is provided between the engine and the heat recirculator. The engine coolant temperature sensor (for exhaust heat recirculation system) has a built-in thermistor with a resistance that varies according to the temperature of the engine coolant. When the engine coolant temperature becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance decreases. These variations in resistance are transmitted to the combination meter sub-assembly as voltage changes. When the temperature becomes high (overheating), the engine coolant temperature sensor sends a signal to the combination meter sub-assembly and illuminates or blinks the water temperature indicator light in the combination meter sub-assembly. If the circuit is malfunctioning, the engine coolant temperature sensor sends a signal to the combination meter sub-assembly and illuminates the water temperature indicator light in the combination meter sub-assembly.

A248795E01
0.094,0.112 0.273,0.312 0.179,0.199 10 *a 0.094,4.261 0.273,4.461 0.179,0.199 10 *b 1.771,4.934 1.950,5.095 0.179,0.160 10 *2 2.217,5.358 2.396,5.558 0.179,0.199 10 *4 3.803,7.338 4.066,7.537 0.263,0.199 10 *10 4.788,6 4.967,6.150 0.179,0.150 10 *8 5.011,6.783 5.190,6.952 0.179,0.169 10 *c 5.011,7.142 5.190,7.342 0.179,0.199 10 *f 6.622,7.439 6.801,7.599 0.179,0.160 10 *e 0.749,1.35 0.928,1.549 0.179,0.199 10 *1 2.284,1.703 2.463,1.857 0.179,0.155 10 *3 2.929,1.831 3.108,1.989 0.179,0.158 10 *4 5.552,1.072 5.731,1.222 0.179,0.150 10 *7 4.772,2.326 4.952,2.486 0.179,0.160 10 *8 5.028,3.291 5.207,3.490 0.179,0.199 10 *c 3.711,3.83 3.890,3.996 0.179,0.166 10 *9 1.347,2.505 1.526,2.671 0.179,0.166 10 *5 1.795,2.883 1.975,3.039 0.179,0.156 10 *6 5.005,3.627 5.184,3.826 0.179,0.199 10 *f 6.557,4.018 6.731,4.176 0.174,0.158 10 *d 2.202,0.58 2.381,0.733 0.179,0.153 10 *2 2.143,1.517 2.221,1.76 2.221,1.76 2.262,1.76 false 2.764,1.606 2.872,1.898 2.872,1.898 2.913,1.898 false 1.784,2.163 1.612,2.566 1.612,2.566 1.521,2.566 false 2.23,2.695 2.026,2.945 2.026,2.945 1.973,2.945 false 3.464,3.363 3.625,3.897 3.625,3.897 3.689,3.897 false 4.516,2.662 4.679,2.397 4.679,2.397 4.743,2.397 false 2.639,5.112 2.449,5.429 2.449,5.429 2.405,5.429 false 3.559,6.982 3.708,7.402 3.708,7.402 3.78,7.402 false 4.511,6.272 4.718,6.065 4.718,6.065 4.761,6.065 false 5.594,4.502 6.478,4.074 6.478,4.074 6.525,4.074 false 5.996,7.822 6.528,7.51 6.528,7.51 6.6,7.51 false

Text in Illustration
*1 Engine Assembly *2 Engine Coolant
*3 Engine Coolant Temperature Sensor (for Exhaust Heat Recirculation System) *4 Exhaust Pipe Gas Control Actuator Sub-assembly
*5 Front Catalyst *6 Rear Catalyst
*7 Combination Meter Sub-assembly *8 Front Exhaust Pipe Assembly
*9 Exhaust Flow Control Valve (Valve Closed) *10 Exhaust Flow Control Valve (Valve Open)
*a Exhaust Flow Control Valve (Valve Closed) *b Exhaust Flow Control Valve (Valve Open)
*c Exhaust Gas *d Valve Closed
*e Valve Open *f Side View

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - COMBINATION METER SUB-ASSEMBLY)
a.

Disconnect the G1 engine coolant temperature sensor (for exhaust heat recirculation system) connector.


b.

Disconnect the L27 combination meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 - L27-8 (TWS3) Always Below 1 Ω
G1-1 - L27-9 (E2) Always Below 1 Ω
G1-2 or L27-8 (TWS3) - Body ground Always 10 kΩ or higher




OK

2.INSPECT ENGINE COOLANT TEMPERATURE SENSOR (FOR EXHAUST HEAT RECIRCULATION SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - COMBINATION METER SUB-ASSEMBLY)

2.INSPECT ENGINE COOLANT TEMPERATURE SENSOR (FOR EXHAUST HEAT RECIRCULATION SYSTEM)
a.

Inspect the engine coolant temperature sensor (for exhaust heat recirculation system) (See page Engine / Hybrid System>2ZR-FXE (COOLING)>TEMPERATURE SWITCH>INSPECTION).

Result
Result Proceed to
OK (w/o Multi-information display) A
OK (w/ Multi-information display) B
NG C



A

REPLACE METER CIRCUIT PLATE (COMBINATION METER SUB-ASSEMBLY)

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (FOR EXHAUST HEAT RECIRCULATION SYSTEM)