A buzzer sounds to alert the driver when the vehicle-to-vehicle distance becomes less than the set value.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1A4A | While power switch is on (IG), skid control buzzer circuit malfunction signal is received by brake booster with master cylinder (skid control ECU) for 1 second or more while the dynamic radar cruise control is operating | ·
Electronically controlled brake system ·
Driving support ECU assembly |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test / DSS Signal Buzzer.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| DSS Signal Buzzer | Skid control buzzer | OFF or ON | Buzzer can be heard |
Skid control buzzer sounds.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).
Turn the cruise control switch (ON-OFF button).
Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1A4A is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Replace the driving support ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).
Turn the cruise control system on using the cruise control switch (ON-OFF button).
Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1A4A is output | B |
A
B
Replace the brake booster with master cylinder (skid control ECU) (for LHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL).
Replace the brake booster with master cylinder (skid control ECU) (for RHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).
Turn the cruise control system on using the cruise control switch (ON-OFF button).
Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1A4A is output | B |
A
B