Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2013.08–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

A buzzer sounds to alert the driver when the vehicle-to-vehicle distance becomes less than the set value.

DTC No. DTC Detection Condition Trouble Area
C1A4A While power switch is on (IG), skid control buzzer circuit malfunction signal is received by brake booster with master cylinder (skid control ECU) for 1 second or more while the dynamic radar cruise control is operating
·

Electronically controlled brake system

·

Driving support ECU assembly



WIRING DIAGRAM

E230011E08
1.292,0.479 1.708,0.646 0.417,0.167 10 false CA1H 1.313,0.979 1.729,1.146 0.417,0.167 10 false CA1L 2.938,0.49 3.354,0.656 0.417,0.167 10 false CA1H 2.938,0.99 3.354,1.156 0.417,0.167 10 false CA1L 5.521,0.479 5.938,0.646 0.417,0.167 10 false CA2H 5.521,0.99 5.938,1.156 0.417,0.167 10 false CA2L 3.906,0.479 4.323,0.646 0.417,0.167 10 false CA2H 3.906,0.99 4.323,1.156 0.417,0.167 10 false CA2L 1.76,0.302 1.938,0.479 0.177,0.177 10 false 37 1.75,0.792 1.927,0.969 0.177,0.177 10 false 38 2.646,0.281 2.823,0.458 0.177,0.177 10 false 25 2.646,0.802 2.823,0.979 0.177,0.177 10 false 24 1.75,2.844 1.927,3.021 0.177,0.177 10 false 13 2.823,2.833 2.938,3.01 0.115,0.177 10 false 1 4.417,0.281 4.594,0.458 0.177,0.177 10 false 34 4.417,0.781 4.594,0.958 0.177,0.177 10 false 35 5.271,0.313 5.448,0.49 0.177,0.177 10 false 39 5.281,0.802 5.458,0.979 0.177,0.177 10 false 17 2.646,0.479 2.938,0.667 0.292,0.188 10 false L6 2.646,0.99 2.938,1.229 0.292,0.24 10 false L6 1.458,2.948 1.688,3.083 0.229,0.135 10 false BZ 3.031,2.958 3.26,3.094 0.229,0.135 10 false BZ 4.417,0.49 4.708,0.688 0.292,0.198 10 false L5 4.427,0.979 4.667,1.146 0.24,0.167 10 false L5 5.313,1.531 5.76,1.74 0.448,0.208 10 false L60 2.958,1.604 4.208,1.99 1.25,0.385 10 false Power Management Control ECU 5.594,1.531 6.906,1.875 1.313,0.344 10 false Driving Support ECU Assembly 0.094,3.552 0.583,3.771 0.49,0.219 10 false A58 0.396,3.552 2.313,3.958 1.917,0.406 10 false Brake Booster with Master Cylinder (Skid Control ECU) 2.719,3.552 3.125,3.76 0.406,0.208 10 false L46 3.021,3.552 4.333,3.729 1.313,0.177 10 false Skid Control Buzzer 5.26,3.313 7.031,3.51 1.771,0.198 10 false : CAN Communication Line

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SKID CONTROL BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test / DSS Signal Buzzer.


e.

Perform the Active Test.

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
DSS Signal Buzzer Skid control buzzer OFF or ON Buzzer can be heard

OK:

Skid control buzzer sounds.




OK

2.CHECK FOR DTCs (DTC C1A4A)

NG

2.CHECK FOR DTCs (DTC C1A4A)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A4A is output B




A

B

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).



NEXT

4.CHECK FOR DTCs (DTC C1A4A)
4.CHECK FOR DTCs (DTC C1A4A)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A4A is output B




A

END

B

5.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER
5.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER
a.

Replace the brake booster with master cylinder (skid control ECU) (for LHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL).


b.

Replace the brake booster with master cylinder (skid control ECU) (for RHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL).



NEXT

6.CHECK FOR DTCs (DTC C1A4A)
6.CHECK FOR DTCs (DTC C1A4A)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A4A is output B




A

END

B