When the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the brake booster with master cylinder (skid control ECU) via CAN communication, DTC C1A50 is stored.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1A50 | When signal malfunction from brake booster with master cylinder (skid control ECU) continues for 1 second while dynamic radar cruise control is operating | ·
Electronically controlled brake system ·
Driving support ECU assembly |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).
Turn the cruise control system on using the cruise control switch (ON-OFF button).
Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1A50 is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Replace the driving support ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).
Turn the cruise control system on using the cruise control switch (ON-OFF button).
Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1A50 is output | B |
A
B
Replace the brake booster with master cylinder (skid control ECU) (for LHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL).
Replace the brake booster with master cylinder (skid control ECU) (for RHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).
Turn the cruise control system on using the cruise control switch (ON-OFF button).
Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1A50 is output | B |
A
B