The brake booster with master cylinder assembly (skid control ECU) receives vehicle stability signals from the yaw rate sensor (airbag ECU assembly) and sends the signals to the lane departure warning camera. If the brake booster with master cylinder assembly (skid control ECU) or yaw rate sensor (airbag ECU assembly) detects that the yaw rate sensor (airbag ECU assembly) is malfunctioning, the brake booster with master cylinder assembly (skid control ECU) or yaw rate sensor (airbag ECU assembly) sends a malfunction signal to the lane departure warning camera and the lane departure warning camera stores DTC C1AA4, C1AA5 or C1AA6.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1AA4 | While driving with the lane departure alert system activated, a yaw rate sensor (airbag ECU assembly) malfunction signal sent from the yaw rate sensor (airbag ECU assembly) to the lane departure warning camera is detected for 5 seconds or more. | ·
Lane departure warning camera ·
Yaw rate sensor (Airbag ECU assembly) |
| C1AA5 | While driving with the lane departure alert system activated, a yaw rate sensor power supply voltage malfunction signal sent from the yaw rate sensor (airbag ECU assembly) to the lane departure warning camera is detected for 5 seconds or more. | ·
Lane departure warning camera ·
Yaw rate sensor (Airbag ECU assembly) |
| C1AA6 | While driving with the lane departure alert system activated, a yaw rate sensor zero point malfunction signal sent from the brake booster with master cylinder assembly (skid control ECU) to the lane departure warning camera is detected for 5 seconds or more. | ·
Electronically controlled brake system ·
Lane departure warning camera |
When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT).
When replacing the lane departure warning camera, always replace it with a new one. If a lane departure warning camera which was installed to another vehicle is used, the information stored in the lane departure warning camera will not match the information from the vehicle. As a result, a DTC may be stored.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Airbag system DTCs are not output | A |
| Airbag system DTCs are output | B |
A
B
(See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Electronically controlled brake system DTCs are not output | A |
| Electronically controlled brake system DTCs are output | B |
A
B
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1AA4, C1AA5 and C1AA6 are not output | A |
| DTC C1AA4, C1AA5 or C1AA6 is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B