Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › from 2013.08
RM2070E _53 Suspension _061919 FRONT SUSPENSION _0301671 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 52256 2.INSTALL FRONT SUSPENSION MEMBER FRONT BRACE LH

Hide 52255 3.INSTALL FRONT SUSPENSION MEMBER FRONT BRACE RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 4.TEMPORARILY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C237863

Temporarily tighten the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48068 5.TEMPORARILY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 57104E 7.INSTALL FRONT CROSS MEMBER SUB-ASSEMBLY

a.

Using a jack, support the engine and transaxle assembly.


b.

Install the front cross member sub-assembly with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


c.
C205607E06
1.5,0.854 1.646,1.021 0.146,0.167 10 true A 1.479,1.125 1.635,1.281 0.156,0.156 10 true B

Connect the front engine mounting insulator with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Temporarily tighten bolt B and then fully tighten the 2 bolts in the order of A and B.



Hide 51201 8.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

NOTICE:
·

Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.

·

Use the attachments to keep the front suspension crossmember sub-assembly level.

·

The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.




b.

Tighten 2 bolts on the left and right sides while alternately inserting SST into the left and right side reference holes in the front suspension crossmember sub-assembly.

C236466E01
2.105,3.71 0.811,3.71 false 5.14,3.71 6.434,3.71 false 6.447,3.642 6.742,3.790 0.295,0.148 10 SST 0.521,3.642 0.816,3.790 0.295,0.148 10 SST 1.352,5.521 1.521,5.678 0.169,0.157 10 *a 2.221,5.521 2.389,5.678 0.169,0.157 10 *b 4.785,5.521 4.953,5.678 0.169,0.157 10 *a 5.625,5.521 5.794,5.678 0.169,0.157 10 *b

Text in Illustration
*a OK *b NG
V100136

Front of the Vehicle - -

SST
09670-00020  

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


c.

Lower the engine lifter.


d.

Install the rear engine mounting insulator with bolts A and B, and nuts C and D by tightening them in several steps.

C236464E03
3.281,1.813 3.406,1.969 0.125,0.156 10 true A 3.292,2.344 3.427,2.531 0.135,0.188 10 true C 4.49,1.802 4.635,1.99 0.146,0.188 10 true B 4.49,2.615 4.615,2.771 0.125,0.156 10 true D

Torque:
Bolt A, B, Nut C, D : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Temporarily tighten bolt A, and then fully tighten the 2 bolts and 2 nuts in the order of B, D, C, and A.



e.

Install the 2 wiring harness clamp brackets with the 2 bolts.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 12361A 9.LOOSEN FRONT ENGINE MOUNTING INSULATOR

a.
C238550

Loosen the bolt and nut from the front engine mounting insulator.

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 12361A 10.FULLY TIGHTEN FRONT ENGINE MOUNTING INSULATOR

a.

Fully tighten the front engine mounting insulator with the bolt and nut.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 52258A 11.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH

a.
C236477E03
1.74,0.167 1.917,0.333 0.177,0.167 10 true A 2.625,1.115 2.75,1.26 0.125,0.146 10 false B 0.833,1.865 0.99,2.042 0.156,0.177 10 true B

Install the front suspension member rear brace LH with 2 bolts B and bolt A.

Torque:
Bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
Bolt B : 93 N*m (948 kgf*cm, 69 ft.*lbf)


Hide 52257 12.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Perform the same procedure as for the LH side.


Hide 51108A 13.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

a.
C205598E07
1.49,0.208 1.625,0.385 0.135,0.177 10 true D 1.99,1.635 2.146,1.813 0.156,0.177 10 true C 2.385,0.198 2.542,0.385 0.156,0.188 10 true A 1.083,1.865 1.229,2.052 0.146,0.188 10 true B

Install the rear side rail reinforcement sub-assembly LH with the 4 bolts.

Torque:
Bolt A, D : 96 N*m (979 kgf*cm, 71 ft.*lbf)
Bolt B, C : 99 N*m (1010 kgf*cm, 73 ft.*lbf)

NOTICE:

Temporarily tighten bolts A and B, and then fully tighten the 4 bolts in the order of C, B, D and A.



Hide 51107A 14.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

a.
C205612E06
0.635,0.198 0.781,0.396 0.146,0.198 10 true A 1.021,1.781 1.156,1.948 0.135,0.167 10 true C 1.552,0.198 1.708,0.375 0.156,0.177 10 true D 1.906,1.813 2.052,1.979 0.146,0.167 10 true B

Install the rear side rail reinforcement sub-assembly RH with the 4 bolts.

Torque:
Bolt A, D : 96 N*m (979 kgf*cm, 71 ft.*lbf)
Bolt B, C : 99 N*m (1010 kgf*cm, 73 ft.*lbf)

NOTICE:

Temporarily tighten bolts A and B, and then fully tighten the 4 bolts in the order of C, B, D and A.



Hide 51425A 15.INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT

a.
C249903E03
2.375,0.521 2.552,0.729 0.177,0.208 10 true A 2.375,1.635 2.552,1.844 0.177,0.208 10 true B

Install the front engine mounting bracket lower reinforcement with the 2 bolts.

Torque:
Bolt A : 96 N*m (979 kgf*cm, 71 ft.*lbf)
Bolt B : 99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 48069 16.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 17.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 18.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 19.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 20.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Install the front stabilizer link assembly LH to the front stabilizer bar with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.


Hide 48820B 21.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45025D 22.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 23.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 24.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 25.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 26. STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Press down on the vehicle several times to stabilize the suspension.


Hide 48069 27.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 28.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51444A 29.INSTALL REAR ENGINE UNDER COVER LH

Hide 51443C 30.INSTALL REAR ENGINE UNDER COVER RH

Hide 51442A 31.INSTALL FRONT NO. 3 ENGINE UNDER COVER

Hide 51442E 32.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 33.INSTALL NO. 1 ENGINE UNDER COVER

Hide 52618A 34.INSTALL FRONT LOWER BUMPER ABSORBER

Hide 35.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT