48725G
1.INSTALL REAR AXLE CARRIER BUSHING LH
Align the arrow mark on a new rear axle carrier bushing LH with the matchmark on the rear axle beam assembly and temporarily install the rear axle carrier bushing LH to the rear axle beam assembly. (If the rear axle beam assembly is reused.)
| *a | Matchmark |
There are 2 different types of rear axle carrier bushing LH. Be sure to confirm the type and install the bushing in the correct direction as shown in the illustration.
Temporarily install the new rear axle carrier bushing LH as shown in the illustration.
| *a | Mark |
| *b | 135° |
|
Upper Side of the Vehicle |
|
Front of the Vehicle |
There are 2 different types of rear axle carrier bushing LH. Be sure to confirm the type and install the bushing in the correct direction as shown in the illustration.
Using SST, install the rear axle carrier bushing LH to the rear axle beam assembly.
| *a | Turn |
| *b | Hold |
Do not damage the rubber portion when installing the rear axle carrier bushing.
Apply grease to the threads and tip of the SST center bolt before use.
48725F
2.INSTALL REAR AXLE CARRIER BUSHING RH
Perform the same procedure as for the LH side.
42110F
3.TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY
Slowly jack up the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools and temporarily install the rear axle beam assembly to the body with the 2 bolts (B).
| *1 | Engine Lifter | *2 | Wooden Block |
| *3 | Attachment | - | - |
Make sure to secure the rear axle beam assembly to prevent it from dropping.
Temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts (A) and 2 nuts.
Since the stopper nuts are used, turn the bolts.
Insert the bolts with the threaded end facing the outside of the vehicle.
48259A
4.INSTALL REAR UPPER COIL SPRING INSULATOR LH
48257C
5.INSTALL REAR UPPER COIL SPRING INSULATOR RH
Perform the same procedure as for the LH side.
48258C
6.INSTALL REAR LOWER COIL SPRING INSULATOR LH
48258B
7.INSTALL REAR LOWER COIL SPRING INSULATOR RH
48231B
8.INSTALL REAR COIL SPRING LH
48231A
9.INSTALL REAR COIL SPRING RH
Perform the same procedure as for the LH side.
89407A
10.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)
11.TEMPORARILY TIGHTEN PARKING BRAKE ASSEMBLY (for LH Side)
Clean the installation surfaces of the parking brake assembly and rear axle beam assembly.
Temporarily tighten the parking brake assembly to the rear axle beam assembly with the nut.
Do not twist the No. 3 parking brake cable assembly when installing the parking brake assembly.
Fully tighten the nut after installing the rear axle hub and bearing assembly.
Install the No. 3 parking brake cable assembly to the rear axle beam assembly with the bolt.
12.TEMPORARILY TIGHTEN PARKING BRAKE ASSEMBLY (for RH Side)
Perform the same procedure as for the LH side.
42450B
13.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH
42450A
14.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH
Perform the same procedure as for the LH side.
15.FULLY TIGHTEN PARKING BRAKE ASSEMBLY (for LH Side)
Fully tighten the nut.
16.FULLY TIGHTEN PARKING BRAKE ASSEMBLY (for RH Side)
Perform the same procedure as for the LH side.
47324
17.INSTALL REAR NO. 4 BRAKE TUBE
Install the rear No. 4 brake tube to the rear axle beam assembly with the nut.
47323
18.INSTALL REAR NO. 3 BRAKE TUBE
Perform the same procedure as for the rear No. 4 brake tube.
47316A
19.CONNECT REAR BRAKE TUBE FLEXIBLE HOSE (for LH Side)
Install the rear brake tube flexible hose with the bolt.
Using a union nut wrench, connect the rear brake tube flexible hose to the rear No. 4 brake tube.
Do not bend or damage the brake line.
Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
47316A
20.CONNECT REAR BRAKE TUBE FLEXIBLE HOSE (for RH Side)
Install the rear brake tube flexible hose with a new clip.
Install the clip as far as it will go.
Using a union nut wrench, connect the rear brake tube flexible hose to the rear No. 3 brake tube.
Do not bend or damage the brake line.
Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
42431
21.INSTALL REAR DISC (for LH Side)
42431
22.INSTALL REAR DISC (for RH Side)
Perform the same procedure as for the LH side.
42491
23.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
Install the 2 parking brake shoe adjusting hole plugs.
24.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH
Install the rear disc brake caliper assembly LH with rear flexible hose LH with the 2 bolts.
Connect the rear flexible hose LH to the rear axle beam assembly with a new clip.
Install the clip as far as it will go.
Using a union nut wrench, connect the rear No. 4 brake tube to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.
Do not bend or damage the brake line.
Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
25.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH
Perform the same procedure as for the LH side.
89516D
26.INSTALL SKID CONTROL SENSOR WIRE LH
89516C
27.INSTALL SKID CONTROL SENSOR WIRE RH
Perform the same procedure as for the LH side.
89516D
28.CONNECT SKID CONTROL SENSOR WIRE LH
89516C
29.CONNECT SKID CONTROL SENSOR WIRE RH
Perform the same procedure as for the LH side.
53605F
30.INSTALL REAR SUSPENSION BRACE SUB-ASSEMBLY
Install the rear suspension brace sub-assembly with the 4 bolts.
31.FILL RESERVOIR WITH BRAKE FLUID
32.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>INSTALLATION).
33.BLEED BRAKE LINE
57627A
34.INSTALL REAR FLOOR SIDE MEMBER COVER RH
Engage the 3 clips to temporarily install the rear floor side member cover RH.
Install the rear floor side member cover RH with the 3 bolts.
35.ADJUST PARKING BRAKE
36.INSTALL REAR WHEELS
37. STABILIZE SUSPENSION
42110F
38.FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY
65638
39.INSTALL REAR WHEEL HOUSE LINER LH
65637
40.INSTALL REAR WHEEL HOUSE LINER RH
Perform the same procedure as for the LH side.
41.INSPECT REAR WHEEL ALIGNMENT
42.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
43.PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION
44.CHECK FOR SPEED SENSOR SIGNAL
45. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL (w/ Height Control Sensor)
46.ADJUST HEADLIGHT AIMING (w/ Height Control Sensor)