Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2013.08–2014.11
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1235/35  Foreign Object is Attached on Tip of Front Speed Sensor RH  C1236/36  Foreign Object is Attached on Tip of Front Speed Sensor LH  C1238/38  Foreign Object is Attached on Tip of Rear Speed Sensor RH  C1239/39  Foreign Object is Attached on Tip of Rear Speed Sensor LH  C1275/75  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276/76  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1277/77  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278/78  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

When foreign matter adheres to the speed sensor tip or speed sensor rotor, these DTCs are output. An abnormal waveform input from the sensor determines these conditions.

These DTCs may be detected when a malfunction occurs in the connector terminals or wire harness of the speed sensor circuit.

DTCs C1275/75 to C1278/78 will be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs from C1275/75 to C1278/78 are output only in Test Mode.

DTC Code INF Code DTC Detection Condition Trouble Area
C1235/35 541 Either of the following is detected:
1.

When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign object attached)

·

Foreign object attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit

·

Brake booster with master cylinder (Skid control ECU)


C1236/36 542 Either of the following is detected:
1.

When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign object attached)

·

Foreign object attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit

·

Brake booster with master cylinder (Skid control ECU)


C1238/38 543 Either of the following is detected:
1.

When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign object attached)

·

Foreign object attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit

·

Brake booster with master cylinder (Skid control ECU)


C1239/39 544 Either of the following is detected:
1.

When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign object attached)

·

Foreign object attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit

·

Brake booster with master cylinder (Skid control ECU)


C1275/75
C1276/76
C1277/77
C1278/78
- Detected only during Test Mode.
·

Speed sensor

·

Speed sensor rotor



HINT:
·

DTCs C1235/35 and C1275/75 are for the front speed sensor RH.

·

DTCs C1236/36 and C1276/76 are for the front speed sensor LH.

·

DTCs C1238/38 and C1277/77 are for the rear speed sensor RH.

·

DTCs C1239/39 and C1278/78 are for the rear speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK DTC
a.

Check that no speed sensor malfunction DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

HINT:

When C1464/31, C1465/32, C1466/33, and/or C1467/34 are output together with C1235/35, C1236/36, C1238/38, and/or C1239/39, inspect and repair the trouble areas indicated by C1464/31, C1465/32, C1466/33, and/or C1467/34 first.


Result:
Result Proceed to
DTCs (C1235/35 and/or C1236/36) are output A
DTCs (C1238/38 and C1239/39) are output B
Speed sensor malfunction DTCs (C1464/31, C1465/32, C1466/33 and/or C1467/34) are output C




A

2.CHECK FRONT SPEED SENSOR AND FRONT SPEED SENSOR ROTOR

B

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

C

2.CHECK FRONT SPEED SENSOR AND FRONT SPEED SENSOR ROTOR

b.

Check the speed sensor tip and speed sensor rotor.

OK:

The sensor tip and rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).





OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR AND FRONT SPEED SENSOR ROTOR

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Install the front speed sensor and front speed sensor rotor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU connector and the front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A58-18 (FR+) - A34-2 (FR+) Always Below 1 Ω
A58-18 (FR+) - Body ground Always 10 kΩ or higher
A58-5 (FR-) - A34-1 (FR-) Always Below 1 Ω
A58-5 (FR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A58-31 (FL+) - A15-2 (FL+) Always Below 1 Ω
A58-31 (FL+) - Body ground Always 10 kΩ or higher
A58-32 (FL-) - A15-1 (FL-) Always Below 1 Ω
A58-32 (FL-) - Body ground Always 10 kΩ or higher




OK

4.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
U154693E03
2.615,2.281 2.885,2.76 false 0.323,0.25 0.563,0.427 0.24,0.177 10 false *a 1.156,2.802 1.448,2.948 0.292,0.146 10 false FR+ 2.802,2.781 3.094,2.927 0.292,0.146 10 false FL+ 0.26,1.302 0.594,1.49 0.333,0.188 10 false A34 1.844,1.302 2.135,1.479 0.292,0.177 10 false A15

Reconnect the skid control ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
A34-2 (FR+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH:
Tester Connection Condition Specified Condition
A15-2 (FL+) - Body ground Power switch on (IG) 5.7 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Front Speed Sensor)

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

5.RECONFIRM DTC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

5.RECONFIRM DTC
a.

Turn the power switch off (lock).


b.

Reconnect the front speed sensor connector.



d.

Turn the power switch on (ready).


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


f.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1235/35 and/or C1236/36) are output A
DTCs (C1235/35 and C1236/36) are not output B




A

6.REPLACE FRONT SPEED SENSOR

B

6.REPLACE FRONT SPEED SENSOR
a.

Turn the power switch off (lock).




NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1235/35 and/or C1236/36) are output A
DTCs (C1235/35 and C1236/36) are not output B




A

8.REPLACE FRONT SPEED SENSOR ROTOR

B

END

8.REPLACE FRONT SPEED SENSOR ROTOR
a.

Turn the power switch off (lock).


b.

Replace the front axle hub sub-assembly (front speed sensor rotor) (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).

HINT:

The front speed sensor rotor is incorporated into the front axle hub sub-assembly.

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1235/35 and/or C1236/36) are output (for LHD) A
DTCs (C1235/35 and/or C1236/36) are output (for RHD) B
DTCs (C1235/35 and C1236/36) are not output C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

END

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)
a.
U154691E01
0.224,0.2 0.428,0.351 0.203,0.151 10 *a 1.181,2.794 1.388,2.950 0.207,0.155 10 *b 1.095,0.843 1.334,0.986 0.239,0.143 10 z2 1.446,0.843 1.649,1.006 0.202,0.163 10 *A 2.634,2.554 2.841,2.709 0.207,0.155 10 *c 2.439,1.049 2.742,1.212 0.303,0.163 10 zS1 2.83,1.049 3.046,1.212 0.216,0.163 10 *A 1.095,1.138 1.334,1.281 0.239,0.143 10 z1 1.446,1.138 1.649,1.301 0.202,0.163 10 *B 2.439,1.345 2.733,1.508 0.294,0.163 10 zR1 2.83,1.345 3.046,1.508 0.216,0.163 10 *B

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the rear speed sensor connector and the skid control sensor wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
z2-2 - zS1-1 Always Below 1 Ω
z2-2 - zS1-2 Always 10 kΩ or higher
z2-2 - Body ground Always 10 kΩ or higher
z2-1 - zS1-2 Always Below 1 Ω
z2-1 - zS1-1 Always 10 kΩ or higher
z2-1 - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
z1-2 - zR1-1 Always Below 1 Ω
z1-2 - zR1-2 Always 10 kΩ or higher
z1-2 - Body ground Always 10 kΩ or higher
z1-1 - zR1-2 Always Below 1 Ω
z1-1 - zR1-1 Always 10 kΩ or higher
z1-1 - Body ground Always 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




OK

11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)

NG

11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A58-22 (RR+) - zS1-1 (RR+) Always Below 1 Ω
A58-22 (RR+) - Body ground Always 10 kΩ or higher
A58-9 (RR-) - zS1-2 (RR-) Always Below 1 Ω
A58-9 (RR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A58-20 (RL+) - zR1-1 (RL+) Always Below 1 Ω
A58-20 (RL+) - Body ground Always 10 kΩ or higher
A58-7 (RL-) - zR1-2 (RL-) Always Below 1 Ω
A58-7 (RL-) - Body ground Always 10 kΩ or higher




OK

12.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
U154775E03
2.625,2.052 2.865,2.521 false 0.323,0.25 0.563,0.427 0.24,0.177 10 false *a 1.219,2.563 1.573,2.708 0.354,0.146 10 false RR+ 2.719,2.542 3.01,2.688 0.292,0.146 10 false RL+ 0.313,1.073 0.656,1.25 0.344,0.177 10 false zS1 1.74,1.073 2.01,1.219 0.271,0.146 10 false zR1

Reconnect the skid control ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
zS1-1 (RR+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH:
Tester Connection Condition Specified Condition
zR1-1 (RL+) - Body ground Power switch on (IG) 5.7 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control Sensor Wire)

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

13.RECONFIRM DTC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

13.RECONFIRM DTC
a.

Turn the power switch off (lock).


b.

Reconnect the rear speed sensor connector and the skid control sensor wire.



d.

Turn the power switch on (ready).


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


f.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1238/38 and/or C1239/39) are output A
DTCs (C1238/38 and C1239/39) are not output B




A

14.REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR

B

14.REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR
a.

Turn the power switch off (lock).


b.

Replace the rear speed sensor and the rear axle hub and bearing assembly (rear speed sensor rotor) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




NEXT

15.RECONFIRM DTC
15.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1238/38 and/or C1239/39) are output (for LHD) A
DTCs (C1238/38 and/or C1239/39) are output (for RHD) B
DTCs (C1238/38 and C1239/39) are not output C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

END