Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.03–2013.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1249/49  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the brake pedal operation status.

The skid control ECU has an open detection circuit, which outputs this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC Code INF Code DTC Detection Condition Trouble Area
C1249/49 231 When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or more.
·

Wire harness or connector

·

Stop light switch

·

Brake booster with master cylinder (Skid control ECU)



WIRING DIAGRAM

C209757E09
5.833,4.896 7.021,5.365 1.188,0.469 10 false Brake Booster with Master Cylinder 2.896,3.406 4.542,3.906 1.646,0.5 10 false Stop Light Control Relay 0.906,4.396 2.083,4.823 1.177,0.427 10 false Stop Light Switch 1.104,2.271 1.958,2.677 0.854,0.406 10 false from Auxiliary Battery 1.135,1.01 1.698,1.302 0.563,0.292 10 false STOP 2.729,0.885 3.25,1.219 0.521,0.333 10 false +B 2.521,0.781 2.792,1.031 0.271,0.25 10 false 6 2.531,1.542 2.854,1.802 0.323,0.26 10 false 8 2.729,1.646 3.156,1.906 0.427,0.26 10 false GND 2.729,2.385 3.188,2.688 0.458,0.302 10 false STP 2.531,2.281 2.802,2.521 0.271,0.24 10 false 5 3.885,2.396 4.354,2.656 0.469,0.26 10 false OUT 4.271,2.26 4.49,2.469 0.219,0.208 10 false 1 3.75,1.625 4.292,1.938 0.542,0.313 10 false ESS1* 4.281,1.531 4.5,1.781 0.219,0.25 10 false 4 3.885,0.865 4.302,1.135 0.417,0.271 10 false ACC 4.302,0.76 4.5,0.969 0.198,0.208 10 false 9 6.135,0.865 6.656,1.177 0.521,0.313 10 false STP0 5.948,0.75 6.229,0.979 0.281,0.229 10 false 3 6.135,1.635 6.646,1.906 0.51,0.271 10 false EXO* 5.885,1.531 6.177,1.792 0.292,0.26 10 false 21 6.135,2.385 6.635,2.667 0.5,0.281 10 false STP2 5.927,2.281 6.115,2.427 0.188,0.146 10 false 6 6.125,4.083 6.635,4.281 0.51,0.198 10 false STP 5.844,3.99 6.208,4.208 0.365,0.219 10 false 33 1.76,3.979 1.917,4.135 0.156,0.156 10 false 1 0.615,3.969 0.76,4.125 0.146,0.156 10 false 2 3,4.792 4.49,5.01 1.49,0.219 10 false to Stop Light Circuit 2.583,3.406 3.042,3.708 0.458,0.302 10 false A28 0.594,4.396 0.969,4.625 0.375,0.229 10 false A26 2.667,5.25 4.802,5.542 2.135,0.292 10 false *: w/ Emergency Brake Signal 5.51,4.896 6.021,5.094 0.51,0.198 10 false A58

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF




OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

NG

4.INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)
2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

3.RECONFIRM DTC

NG

8.INSPECT SKID CONTROL ECU (STP TERMINAL)
3.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (ready).


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1249/49) is not output A
DTC (C1249/49) is output (for LHD) B
DTC (C1249/49) is output (for RHD) C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

4.INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)
a.

Check that the STOP (10 A) fuse is normal.


U190992E02
0.25,0.198 0.479,0.344 0.229,0.146 10 false *a 0.542,1.167 0.969,1.479 0.427,0.313 10 false A26

b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the stop light switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A26-2 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch)



OK

5.INSPECT STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.INSPECT STOP LIGHT SWITCH
a.
C213075E03
0.299,0.299 0.511,0.497 0.211,0.198 10 *a 1.587,1.921 0.965,1.233 false 0.867,1.038 0.995,1.236 0.128,0.198 10 2 1.875,1.921 2.498,1.233 false 2.517,1.038 2.645,1.236 0.128,0.198 10 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Switch pin free Below 1 Ω
1 - 2 Switch pin pushed in 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Stop Light Switch)



OK

6.INSPECT SKID CONTROL ECU (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH

6.INSPECT SKID CONTROL ECU (STP TERMINAL)
a.
U191011E02
1.552,2.135 1.063,2.802 true 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.281,0.875 0.573,1.031 0.292,0.156 10 false A58 0.896,2.813 1.208,2.969 0.313,0.156 10 false STP

Reconnect the stop light switch connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-33 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V
A58-33 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

7.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.



c.

Turn the power switch on (ready).


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1249/49) is not output A
DTC (C1249/49) is output (for LHD) B
DTC (C1249/49) is output (for RHD) C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

8.INSPECT SKID CONTROL ECU (STP TERMINAL)
a.
U191011E02
1.552,2.135 1.063,2.802 true 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.281,0.875 0.573,1.031 0.292,0.156 10 false A58 0.896,2.813 1.208,2.969 0.313,0.156 10 false STP

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-33 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V
A58-33 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)