Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.03–2014.11
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1234/34  Yaw Rate Sensor Malfunction  C1243/43  Acceleration Sensor Stuck Malfunction  C1244/44  Open or Short in Acceleration Sensor Circuit  C1245/45  Acceleration Sensor Output Malfunction  C1279/79  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  C1381/97  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.

The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there are any problems in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123/62 (Lost Communication with Yaw Rate Sensor Module) and U0124/95 (Lost Communication with Lateral Acceleration Sensor Module) are output.

These DTCs are also output when calibration has not been completed.

DTC C1279/79 will be cleared when the yaw rate and acceleration sensor sends a yaw rate and/or acceleration signal or when Test Mode ends. DTC C1279/79 is output only in Test Mode.

DTC Code INF Code DTC Detection Condition Trouble Area
C1234/34 711 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 1 (GL1) malfunction). Yaw rate and acceleration sensor internal malfunction
↑ 712 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Sensor 2 (GL2) malfunction). ↑
↑ 713 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Zero point calibration malfunction). ↑
↑ 714 While yaw rate sensor communication is enabled, a malfunction signal output is received during the sensor self-check (Two-value comparison malfunction). ↑
C1243/43 561 An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h (19 mph) to 0 km/h (0 mph). Yaw rate and acceleration sensor internal stuck malfunction
↑ 562
563
564
A stuck acceleration sensor value is determined. ↑
C1244/44 571 Either of the following is detected:
1.

Difference between GL1 and GL2 does not become less than 0.4 G for 60 seconds or more after reaching 0.6 G when the vehicle is stopped.

2.

A malfunction signal from the acceleration sensor is received.


·

Yaw rate and acceleration sensor installed improperly

·

Yaw rate and acceleration sensor


C1245/45 581 Difference between longitudinal G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Yaw rate and acceleration sensor installed improperly

·

Yaw rate and acceleration sensor


C1381/97 601 While yaw rate and acceleration sensor communication is enabled, a supply voltage malfunction signal is received from the sensor for 10 seconds.
·

Yaw rate and acceleration sensor supply voltage shut down

·

Yaw rate and acceleration sensor

·

Brake booster with master cylinder (Skid control ECU)


C1279/79 - Detected only during Test Mode.
·

Sensor installation

·

Yaw rate and acceleration sensor



WIRING DIAGRAM

C167661E48
0.167,4.021 0.438,4.177 0.271,0.156 10 false L12 5.844,4.031 7.052,4.385 1.208,0.354 10 false Brake Booster with Master Cylinder 6.042,1.521 6.469,1.667 0.427,0.146 10 false CA1H 6.042,0.635 6.469,0.781 0.427,0.146 10 false CA1L 5.531,4.031 5.792,4.188 0.26,0.156 10 false A58 5.802,1.427 6,1.583 0.198,0.156 10 false 37 5.802,0.552 6,0.708 0.198,0.156 10 false 38 3.906,2.344 5.354,2.5 1.448,0.156 10 false from IG1 NO. 1 Relay 2.083,2.5 2.99,2.656 0.906,0.156 10 false ECU-IG NO. 2 1.281,3.042 1.406,3.208 0.125,0.167 10 false 1 1.281,2.229 1.406,2.396 0.125,0.167 10 false 4 1.281,1.417 1.406,1.583 0.125,0.167 10 false 3 1.281,0.552 1.406,0.719 0.125,0.167 10 false 2 0.792,1.521 1.219,1.667 0.427,0.146 10 false CANH 1.031,2.323 1.219,2.469 0.188,0.146 10 false IG 0.854,3.135 1.219,3.281 0.365,0.146 10 false GND 0.792,0.635 1.219,0.781 0.427,0.146 10 false CANL 0.458,4.031 1.74,4.354 1.281,0.323 10 false Yaw Rate and Acceleration Sensor

CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).


HINT:

When U0123/62 and/or U0124/95 is output together with C1234/34, C1243/43, C1244/44, C1245/45, and/or C1381/97, inspect and repair the trouble areas indicated by U0123/62 and/or U0124/95 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>U0073/94).


PROCEDURE

1.CHECK DTC

b.

Turn the power switch off (lock).


c.

Turn the power switch on (ready).


d.

Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Turn the power switch on (IG) again and check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).


f.

Check if DTC C1210/36 (Zero Point Calibration of Yaw Rate Sensor Undone) or C1336/98 (Zero Point Calibration of Acceleration Sensor Undone) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1210/36, C1336/98 and CAN communication system DTC) are not output A
CAN communication system DTC is output B
DTCs (C1210/36 and/or C1336/98) are output C




A

2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION

B

C

2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
a.

Turn the power switch off (lock).


b.

Check that the yaw rate and acceleration sensor has been installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR>INSTALLATION).

OK:

The sensor is tightened to the specified torque.

The sensor is not tilted.




OK

3.INSPECT YAW RATE AND ACCELERATION SENSOR (IG TERMINAL)

NG

INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY

3.INSPECT YAW RATE AND ACCELERATION SENSOR (IG TERMINAL)
a.
U154836E01
2.024,2.909 2.201,3.051 0.178,0.142 10 IG 0.385,1.017 0.664,1.172 0.279,0.155 10 L12 0.221,0.248 0.446,0.423 0.225,0.176 10 *a 1.783,2.311 2.089,2.881 false

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the yaw rate and acceleration sensor connector.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L12-4 (IG) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor)



OK

4.INSPECT YAW RATE AND ACCELERATION SENSOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

4.INSPECT YAW RATE AND ACCELERATION SENSOR (GND TERMINAL)
a.
U154837E01
0.769,2.909 1.127,3.051 0.358,0.142 10 GND 0.385,1.017 0.664,1.172 0.279,0.155 10 L12 0.221,0.248 0.446,0.423 0.225,0.176 10 *a 1.298,2.311 0.992,2.881 false

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L12-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor)

NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)