Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2013.08–2014.11
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Skid Control Buzzer Circuit  


DESCRIPTION

A buzzer sounds to alert the driver when the vehicle-to-vehicle distance becomes less than the set value (for vehicles with a dynamic radar cruise control).

WIRING DIAGRAM

C209400E22
6.083,2.125 6.5,2.26 0.417,0.135 10 false GND 6.083,2.729 6.5,2.865 0.417,0.135 10 false GND2 6.083,3.333 6.5,3.469 0.417,0.135 10 false GND3 6.083,3.917 6.5,4.052 0.417,0.135 10 false GND4 6.083,4.521 6.5,4.656 0.417,0.135 10 false GND5 6.083,5.135 6.5,5.271 0.417,0.135 10 false GND6 6.083,1.125 6.292,1.271 0.208,0.146 10 false BZ 5.49,6.031 5.771,6.177 0.281,0.146 10 false A58 4,1.573 5.26,1.708 1.26,0.135 10 false Skid Control Buzzer 5.792,1.021 5.969,1.156 0.177,0.135 10 false 13 5.104,1.021 5.198,1.156 0.094,0.135 10 false 1 3.729,1.021 3.823,1.156 0.094,0.135 10 false 2 4.813,1.177 5.031,1.313 0.219,0.135 10 false BZ 3.667,1.573 3.948,1.719 0.281,0.146 10 false L46 3.927,1.188 4.24,1.333 0.313,0.146 10 false IG1 5.792,2.031 5.969,2.167 0.177,0.135 10 false 28 5.792,2.625 5.969,2.76 0.177,0.135 10 false 27 5.792,3.229 5.969,3.365 0.177,0.135 10 false 26 5.792,3.813 5.969,3.948 0.177,0.135 10 false 25 5.792,4.417 5.969,4.552 0.177,0.135 10 false 24 5.792,5.031 5.969,5.167 0.177,0.135 10 false 23 2.448,1.313 3.385,1.448 0.938,0.135 10 false ECU-IG NO. 2 0.271,1.167 1.667,1.365 1.396,0.198 10 false from IG1 NO. 1 Relay 5.833,6.031 7.042,6.396 1.208,0.365 10 false Brake Booster with Master Cylinder

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK BUZZER OPERATION
a.

Confirm problem symptoms of the skid control buzzer according to the customer problem analysis.

Result:
Result Proceed to
Buzzer does not sound A
Buzzer sounds constantly B




A

2.PERFORM ACTIVE TEST USING GTS (SKID CONTROL BUZZER)

B

7.INSPECT SKID CONTROL ECU
2.PERFORM ACTIVE TEST USING GTS (SKID CONTROL BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Active Test on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
DSS Signal Buzzer Skid control buzzer Buzzer ON/OFF Buzzer can be heard


d.

Check that the buzzer sounds/stops when turning the skid control buzzer on/off using the GTS.

Result:
Result Proceed to
Buzzer does not sound A
Buzzer sounds/stops B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

3.INSPECT SKID CONTROL BUZZER (POWER SOURCE TERMINAL)

B

3.INSPECT SKID CONTROL BUZZER (POWER SOURCE TERMINAL)
a.
U190993E02
1.844,2.438 2.25,3.01 false 0.292,0.26 0.531,0.458 0.24,0.198 10 false *a 0.521,1.406 0.844,1.594 0.323,0.188 10 false L46 2.188,3.021 2.458,3.208 0.271,0.188 10 false IG1

Turn the power switch off (lock).


b.

Disconnect the skid control buzzer connector.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L46-2 (IG1) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control Buzzer)



OK

4.INSPECT SKID CONTROL BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.INSPECT SKID CONTROL BUZZER
a.

Turn the power switch off (lock).


C181788E32
1.979,0.771 2.26,1.854 false 2.792,0.771 2.479,1.854 false 0.25,0.177 0.469,0.344 0.219,0.167 10 false *a 2.646,0.573 2.948,0.74 0.302,0.167 10 false IG1 1.865,0.573 2.115,0.74 0.25,0.167 10 false BZ 1.24,1.906 1.479,2.104 0.24,0.198 10 false (-) 0.51,1.896 0.75,2.094 0.24,0.198 10 false (+)

b.

Connect a negative (-) lead from the auxiliary battery to terminal 1 (BZ), and a positive (+) lead to terminal 2 (IG1) of the skid control buzzer, and then check that the buzzer sounds.

OK:

The skid control buzzer sounds.


Text in Illustration
*a Component without harness connected
(Skid Control Buzzer)

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL BUZZER)

B

C

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL BUZZER)
a.

Disconnect the skid control ECU connector 2 minutes after the power switch is turned off (lock).

HINT:

Do not open/close the driver door within 2 minutes after the power switch is turned off (lock).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-13 (BZ) - L46-1 (BZ) Always Below 1 Ω
A58-13 (BZ) - Body ground Always 10 kΩ or higher




OK

6.INSPECT SKID CONTROL ECU (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SKID CONTROL ECU (GND TERMINAL)
a.
U154749E02
2.26,1.802 2.26,1 false 2.365,1.802 2.708,0.667 false 2.146,1.802 1.802,0.667 false 2.469,1.802 3.01,0.979 false 2.052,1.802 1.5,0.979 false 2.646,1.99 2.938,2.76 false 0.198,0.188 0.406,0.344 0.208,0.156 10 false *a 0.271,0.865 0.563,1.021 0.292,0.156 10 false A58 2.031,0.802 2.438,0.958 0.406,0.156 10 false GND4 1.552,0.49 1.958,0.646 0.406,0.156 10 false GND5 2.49,0.49 2.896,0.646 0.406,0.156 10 false GND3 2.813,0.802 3.219,0.958 0.406,0.156 10 false GND2 1.25,0.802 1.656,0.958 0.406,0.156 10 false GND6 2.771,2.781 3.125,2.938 0.354,0.156 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-28 (GND) - Body ground Always Below 1 Ω
A58-27 (GND2) - Body ground Always Below 1 Ω
A58-26 (GND3) - Body ground Always Below 1 Ω
A58-25 (GND4) - Body ground Always Below 1 Ω
A58-24 (GND5) - Body ground Always Below 1 Ω
A58-23 (GND6) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

7.INSPECT SKID CONTROL ECU
a.

Disconnect the skid control ECU connector.


b.

Check that the skid control buzzer operation.

Result:
Result Proceed to
Buzzer stops (for LHD) A
Buzzer stops (for RHD) B
Buzzer sounds constantly C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

8.REPLACE SKID CONTROL BUZZER
8.REPLACE SKID CONTROL BUZZER
a.

Reconnect the skid control ECU connector.



c.

Check that the skid control buzzer operation.

Result:
Result Proceed to
Buzzer stops A
Buzzer sounds constantly B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

END

B

9.CHECK IF CONNECTOR IS SECURELY CONNECTED
9.CHECK IF CONNECTOR IS SECURELY CONNECTED
a.

Gently jiggle the connectors and wire harnesses and check the skid control buzzer operation.

Result:
Result Proceed to
Buzzer stops A
Buzzer sounds constantly B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

END

B

REPAIR OR REPLACE HARNESS OR CONNECTOR