The skid control ECU is connected to the combination meter sub-assembly via CAN communication.
If any of the following is detected, the brake warning light / red (malfunction) remains on:
The skid control ECU connector is disconnected from the skid control ECU.
The brake fluid level is insufficient.
The parking brake is applied.
EBD operation has been disabled.
When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Check if a ABS, VSC and/or electronically controlled brake system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Check if the skid control ECU connector is securely connected.
The connector is securely connected.
OK
NG
Check the auxiliary battery voltage.
11 to 14 V
OK
NG
Disconnect the skid control ECU connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-16 (IG1) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU) |
OK
NG
Turn the power switch off (lock).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-28 (GND) - Body ground | Always | Below 1 Ω |
| A58-27 (GND2) - Body ground | Always | Below 1 Ω |
| A58-26 (GND3) - Body ground | Always | Below 1 Ω |
| A58-25 (GND4) - Body ground | Always | Below 1 Ω |
| A58-24 (GND5) - Body ground | Always | Below 1 Ω |
| A58-23 (GND6) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Skid Control ECU) |
OK
NG
Reconnect the skid control ECU connector.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Parking Brake SW | Parking brake switch / ON or OFF | ON: Parking brake applied
OFF: Parking brake released |
- |
Using the GTS, check if the switch condition on the GTS changes according to parking brake operation.
The GTS displays ON or OFF according to parking brake operation.
OK
NG
Turn the power switch off (lock).
Perform the Active Test of the combination meter sub-assembly (meter CPU) using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
Check the combination meter sub-assembly.
The brake warning light / red (malfunction) turns on or off in accordance with the GTS operation.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
B
C
Turn the power switch off (lock).
Disconnect the parking brake switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+) - Body ground | Parking brake switch ON
(Switch pin free) |
Below 1 Ω |
| 1 (+) - Body ground | Parking brake switch OFF
(Switch pin pushed in) |
10 kΩ or higher |
| *a | Component without harness connected
(Parking Brake Switch) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2C-20 (PKB) - A25-1 (+) | Always | Below 1 Ω |
| 2C-20 (PKB) - Body ground | Always | 10 kΩ or higher |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
OK
NG