Each solenoid adjusts pressure which affects each wheel cylinder according to signals from the skid control ECU and controls the vehicle.
The master cut solenoid is closed and blocks the regulator pressure from the electronically controlled brake system control pressure when the system is normal. The master cut solenoid is open and sends the master cylinder and regulator hydraulic pressure to the non-assisted brake wheel cylinders during the fail-safe due to a system malfunction.
If the supply voltage decreases, a drop in current may cause a DTC to be stored.
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1211/25 | 21 | Excess current is applied for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 22 | An open is detected for 0.05 seconds or more while the solenoid is OFF. | ↑ |
| ↑ | 23 | An open is detected for 0.05 seconds or more while the solenoid is ON. | ·
Supply voltage reduced ·
Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 24 | A short to +B or voltage leaks is detected for 0.05 seconds. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1212/26 | 31 | Excess current is applied for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 32 | An open is detected for 0.05 seconds or more while the solenoid is OFF. | ↑ |
| ↑ | 33 | An open is detected for 0.05 seconds or more while the solenoid is ON. | ·
Supply voltage reduced ·
Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 34 | A short to +B or voltage leaks is detected for 0.05 seconds. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1225/31 | 41 | Excess current is applied for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 42 | An open is detected for 0.05 seconds or more while the solenoid is OFF. | ↑ |
| ↑ | 43 | An open is detected for 0.05 seconds or more while the solenoid is ON. | ·
Supply voltage reduced ·
Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 44 | A short to +B or voltage leaks are detected for 0.05 seconds. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1226/32 | 51 | Excess current is applied for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 52 | An open is detected for 0.05 seconds or more while the solenoid is OFF. | ↑ |
| ↑ | 53 | An open is detected for 0.05 seconds or more while the solenoid is ON. | ·
Supply voltage reduced ·
Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 54 | A short to +B or voltage leaks are detected for 0.05 seconds. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1227/33 | 61 | Excess current is applied for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 62 | An open is detected for 0.05 seconds or more while the solenoid is OFF. | ↑ |
| ↑ | 63 | An open is detected for 0.05 seconds or more while the solenoid is ON. | ·
Supply voltage reduced ·
Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 64 | A short to +B or voltage leaks are detected for 0.05 seconds. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1228/34 | 71 | Excess current is applied for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 72 | An open is detected for 0.05 seconds or more while the solenoid is OFF. | ↑ |
| ↑ | 73 | An open is detected for 0.05 seconds or more while the solenoid is ON. | ·
Supply voltage reduced ·
Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 74 | A short to +B or voltage leaks are detected for 0.05 seconds. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1352/21 | 11
12 |
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1353/23 | 15
16 |
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1356/22 | 13
14 |
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1357/24 | 17
18 |
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
When replacing the brake booster with master cylinder (skid control ECU or brake actuator), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
If a DTC for undervoltage is output, first troubleshoot the power source system.
| Result | Proceed to |
|---|---|
| DTCs (C1211/25, C1212/26, C1225/31, C1226/32, C1227/33, C1228/34, C1352/21, C1353/23, C1356/22 and C1357/24) are not output | A |
| A DTC (C1241/41) for undervoltage is output | B |
| DTCs (C1211/25, C1212/26, C1225/31, C1226/32, C1227/33, C1228/34, C1352/21, C1353/23, C1356/22 and/or C1357/24) are output (for LHD) | C |
| DTCs (C1211/25, C1212/26, C1225/31, C1226/32, C1227/33, C1228/34, C1352/21, C1353/23, C1356/22 and/or C1357/24) are output (for RHD) | D |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
D