Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD) › 2014.11–2016.05
RM2070E _54 Brake _061924 BRAKE SYSTEM (OTHER) _0301696 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  INSTALLATION  


PROCEDURE

Hide 44785C 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster with master cylinder assembly.


Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C238462E01
2.304,2.667 2.471,2.821 0.167,0.154 10 *1 0.514,2.725 0.682,2.879 0.167,0.154 10 *2 2.976,2.849 3.143,3.003 0.167,0.154 10 *3 2.771,3.754 2.938,3.908 0.167,0.154 10 *4 0.641,4.013 0.808,4.167 0.167,0.154 10 *5 1.853,2.753 2.304,2.753 false 1.716,3.305 0.7,2.818 0.7,2.818 1.277,3.421 false 1.386,3.856 0.827,4.095 0.827,4.095 1.267,4.119 false 2.727,3.195 2.811,2.927 2.811,2.927 2.976,2.927 false 2.426,3.567 2.6,3.834 2.6,3.834 2.77,3.834 false

Install the brake booster with master cylinder assembly with the 4 nuts.

Text in Illustration
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.

·

Be careful not to allow brake fluid to enter the connector of ECU.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.




b.

Engage 2 clamps to install the brake line.


c.
C205682E05
1.677,0.427 1.917,0.177 1.917,0.177 2,0.177 true 1.948,0.719 1.406,0.719 true 1.938,0.927 1.167,0.927 true 1.938,1.177 1.938,1.604 true 2.052,0.594 2.5,0.594 true 2.5,0.51 2.688,0.688 0.188,0.177 10 true *a 1.229,0.625 1.417,0.802 0.188,0.177 10 true *b 0.979,0.844 1.167,1.01 0.188,0.167 10 true *c 1.844,1.604 2.031,1.771 0.188,0.167 10 true *d 2,0.094 2.167,0.24 0.167,0.146 10 false *e

Temporarily tighten each brake line to the correct position on the brake booster with master cylinder assembly as shown in the illustration.

Text in Illustration
*a to Front Wheel Cylinder LH
*b to Rear Wheel Cylinder RH
*c to Brake Booster Pump Assembly
*d to Rear Wheel Cylinder LH
*e to Front Wheel Cylinder RH


d.
C205681E03
2.698,1.281 2.698,1.688 2.698,1.688 2.792,1.688 true 2.813,1.604 2.979,1.75 0.167,0.146 10 false *1

Install the No. 2 brake tube clamp bracket to the brake booster with master cylinder assembly with the 2 bolts.

Text in Illustration
*1 Stopper

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

Securely install the No. 2 brake tube clamp bracket so that its stopper contacts the brake booster with master cylinder assembly as shown in the illustration.



e.

Using a union nut wrench, fully tighten each brake line.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




f.
C205679

Connect the connector.

NOTICE:
·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.

·

Make sure that the connector lock is locked securely.




Hide 44595 3.INSTALL NO. 5 BRAKE ACTUATOR BRACKET

a.
C205680E04
2.854,0.458 3.094,0.688 0.24,0.229 10 true (1) 1.208,1.844 1.448,2.052 0.24,0.208 10 true (2)

Install the No. 5 brake actuator bracket with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Tighten the 2 nuts in the order shown in the illustration.



b.

Engage the clamp.


Hide 44571 4.CONNECT BRAKE ACTUATOR HOSE

a.
C239204E03
1.009,0.239 1.32,0.388 0.311,0.149 10 135° 1.009,0.995 1.32,1.144 0.311,0.149 10 145°

Connect the brake actuator hose to the brake booster pump assembly with the clip.

Text in Illustration
V100136

Front of Vehicle

NOTICE:
·

Make sure to match the identification mark (yellowish green) on the hose with the brake booster pump rib.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47234L 5.CONNECT NO. 1 RESERVOIR HOSE

a.
C239205E03
2.01,2.177 2.563,2.177 false 2.042,2.448 2.542,2.448 false 0.51,0.354 0.75,0.51 0.24,0.156 10 false 60° 1.583,1.063 1.823,1.219 0.24,0.156 10 false 60° 1.583,0.417 1.896,0.573 0.313,0.156 10 false 120° 0.906,0.365 1.219,0.521 0.313,0.156 10 false 180° 0.49,0.135 0.646,0.292 0.156,0.156 10 false *1 1.573,0.135 1.729,0.292 0.156,0.156 10 false *2 2.563,2.083 2.75,2.25 0.188,0.167 10 true *1 2.563,2.375 2.75,2.563 0.188,0.188 10 true *2

Connect the No. 1 reservoir hose and No. 2 reservoir hose to the brake booster with master cylinder assembly with the 2 clips.

Text in Illustration
*1 No. 1 Reservoir Hose
*2 No. 2 Reservoir Hose
V100136

Up

NOTICE:
·

Make sure to match the identification marks on the hoses and brake booster with master cylinder assembly.

Hose Identification Mark Color Brake Booster with Master Cylinder Assembly Identification Mark Color
No. 1 Reservoir Hose White White (Unpainted Color)
No. 2 Reservoir Hose Green Green

·

When connecting the reservoir hose, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47235G 6.CONNECT NO. 2 RESERVOIR HOSE

Hide 7.INSTALL BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET

a.

Install the brake master cylinder reservoir with bracket with the 2 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 47101A 9.INSTALL BRAKE PEDAL RETURN SPRING

Hide 10.FILL RESERVOIR WITH BRAKE FLUID

Hide 11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 13.INSPECT AND ADJUST BRAKE PEDAL

Hide 14. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR

HINT:

After the brake booster with master cylinder assembly is replaced, obtain the zero point of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).


Hide 55701J 15.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

Install the outer cowl top panel sub-assembly with the 9 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
C256208

Bend the water guard plate RH and engage the claw.


c.
C256209

Bend the No. 1 heater air duct splash shield seal and engage the claw.


d.

Engage the clamp to install the wire harness.


Hide 55736D 16.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

a.

Install the cowl body mounting reinforcement LH with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55606 18.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY