Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E360452E04
0.813,0.802 1.427,1 0.615,0.198 10 false MACC 0.813,1.24 1.427,1.438 0.615,0.198 10 false MCO+ 0.833,1.708 1.448,1.906 0.615,0.198 10 false MCO- 5.927,0.813 6.542,1.01 0.615,0.198 10 false MACC 0.854,2.677 1.469,2.875 0.615,0.198 10 false SNS2 5.927,1.26 6.542,1.458 0.615,0.198 10 false MIN+ 5.927,1.75 6.542,1.948 0.615,0.198 10 false MIN- 5.917,2.219 6.531,2.417 0.615,0.198 10 false SGND 5.917,2.667 6.531,2.865 0.615,0.198 10 false SNS2 1.344,0.688 1.5,0.885 0.156,0.198 10 false 2 1.333,1.135 1.594,1.396 0.26,0.26 10 false 3 1.333,1.625 1.49,1.823 0.156,0.198 10 false 4 1.344,2.542 1.5,2.74 0.156,0.198 10 false 5 5.698,0.667 5.854,0.865 0.156,0.198 10 false 4 5.708,1.156 5.865,1.354 0.156,0.198 10 false 5 5.677,1.594 6.042,1.844 0.365,0.25 10 false 19 5.667,2.073 5.938,2.302 0.271,0.229 10 false 18 5.708,2.552 5.865,2.75 0.156,0.198 10 false 6 3.25,2.052 3.958,2.271 0.708,0.219 10 false (Shielded) 0.281,3.104 0.896,3.302 0.615,0.198 10 false U3 0.271,3.271 1.708,3.885 1.438,0.615 10 false Map Light Assembly (Telephone Microphone Assembly) 5.615,3.094 6.229,3.292 0.615,0.198 10 false L35 5.615,3.26 6.823,3.792 1.208,0.531 10 false Radio and Display Receiver Assembly

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E277821

Enter the "Microphone Check" screen.

Refer to Check Microphone in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>OPERATION CHECK).


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.




OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the L35 radio and display receiver assembly connector.


b.

Disconnect the U3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-4 (MACC) - U3-2 (MACC) Always Below 1 Ω
L35-5 (MIN+) - U3-3 (MCO+) Always Below 1 Ω
L35-19 (MIN-) - U3-4 (MCO-) Always Below 1 Ω
L35-6 (SNS2) - U3-5 (SNS2) Always Below 1 Ω
L35-4 (MACC) - Body ground Always 10 kΩ or higher
L35-5 (MIN+) - Body ground Always 10 kΩ or higher
L35-19 (MIN-) - Body ground Always 10 kΩ or higher
L35-18 (SGND) - Body ground Always 10 kΩ or higher
L35-6 (SNS2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
U191431E01
1.569,0.606 1.818,0.787 0.249,0.181 10 L35 0.211,0.148 0.444,0.302 0.232,0.154 10 *a 2.749,2.696 3.195,2.849 0.445,0.154 10 SGND 2.875,1.199 3.321,1.353 0.445,0.154 10 MACC 1.168,2.696 1.516,2.849 0.348,0.154 10 MIN- 2.229,1.996 2.896,2.676 false 2.229,1.72 2.85,1.282 false 2.054,1.996 1.387,2.676 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L35-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-18 (SGND) - Body ground Always Below 1 Ω
L35-19 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly) (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL).


b.
E187117E70
1.76,1.26 1.448,1.708 false 1.906,1.25 2.333,1.688 false 0.104,0.083 0.302,0.281 0.198,0.198 10 false *a 2.281,1.698 2.75,1.906 0.469,0.208 10 false MCO- 1.156,1.719 1.583,1.917 0.427,0.198 10 false SNS2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (SNS2) - 4 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Turn the power switch on (ACC).


b.
U191252E02
1.885,2.094 1.344,2.75 false 2.042,2.083 2.521,2.719 false 1.646,0.563 1.844,0.74 0.198,0.177 10 false U3 0.177,0.073 0.375,0.271 0.198,0.198 10 false *a 2.385,2.76 2.844,2.958 0.458,0.198 10 false MCO+ 1.063,2.76 1.49,2.958 0.427,0.198 10 false MCO-

Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the U3 map light assembly (telephone microphone assembly) connector.


c.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B


Text in Illustration
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))



A

B

6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
6.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL).


b.

Check if the same malfunction recurs.

Result:
Result Proceed to
Malfunction does not recur
(returns to normal)
A
Malfunction recurs B




OK

END

NG

REPLACE MAP LIGHT ASSEMBLY