Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B15D8  Monitor Disconnected  


DESCRIPTION

The radio and display receiver assembly and parking assist ECU are connected via an AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and parking assist ECU.

DTC No. DTC Detection Condition Trouble Area
B15D8 When either of the following conditions is met:
·

The parking assist ECU is not connected while the power switch is on (ACC) or on (IG)

·

Communication between the master unit and the parking assist ECU is not possible when the engine is started


·

Parking assist ECU power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and parking assist ECU

·

Parking assist ECU

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E305052E08
1.188,0.49 2.542,0.823 1.354,0.333 10 false from Auxiliary Battery 1.5,0.979 2.625,1.146 1.125,0.167 10 false from ACC Relay 3.854,2.313 4.24,2.5 0.385,0.188 10 false TX3+ 3.885,2.719 4.24,2.906 0.354,0.188 10 false TX3- 5.635,3.521 6.104,3.708 0.469,0.188 10 false GND1 5.635,2.698 6.021,2.885 0.385,0.188 10 false TX- 5.635,2.302 6.021,2.49 0.385,0.188 10 false TX+ 5.615,1.01 6,1.198 0.385,0.188 10 false ACC 5.615,0.531 6,0.719 0.385,0.188 10 false +B 5.354,2.542 5.542,2.729 0.188,0.188 10 false 10 5.354,2.146 5.531,2.333 0.177,0.188 10 false 11 5.375,0.396 5.563,0.583 0.188,0.188 10 false 1 4.323,2.146 4.5,2.333 0.177,0.188 10 false 7 4.323,2.563 4.5,2.75 0.177,0.188 10 false 8 3.104,3.094 3.521,3.281 0.417,0.188 10 false L169 3.104,3.25 4.49,3.635 1.385,0.385 10 false Radio and Display Receiver Assembly 5.26,4.115 6.76,4.365 1.5,0.25 10 false Parking Assist ECU 3.823,0.667 4.698,0.854 0.875,0.188 10 false RAD NO. 1 3.823,1.135 4.698,1.323 0.875,0.188 10 false ECU-ACC 5.417,3.375 5.615,3.563 0.198,0.188 10 false 4 5.26,3.948 5.698,4.135 0.438,0.188 10 false L64 5.375,0.854 5.563,1.042 0.188,0.188 10 false 9 1.01,4.271 3.375,4.448 2.365,0.177 10 false : AVC-LAN Communication Line 3.76,1.604 4.76,1.792 1,0.188 10 false ECU-IG NO. 2 5.625,1.458 6.01,1.646 0.385,0.188 10 false IG 5.375,1.313 5.563,1.5 0.188,0.188 10 false 8 1.177,1.417 2.573,1.583 1.396,0.167 10 false from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

3.CHECK DTC
3.CHECK DTC

b.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END

NG

4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)
a.

Disconnect the L64 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L64-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L64-1 (+B) - L64-4 (GND1) Power switch off 11 to 14 V
L64-8 (IG) - L64-4 (GND1) Power switch on (IG) 11 to 14 V
L64-9 (ACC) - L64-4 (GND1) Power switch on (ACC) 11 to 14 V




OK

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the L64 parking assist ECU connector.


b.

Disconnect the L169 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L64-11 (TX+) - L169-7 (TX3+) Always Below 1 Ω
L64-10 (TX-) - L169-8 (TX3-) Always Below 1 Ω
L64-11 (TX+) - Body ground Always 10 kΩ or higher
L64-10 (TX-) - Body ground Always 10 kΩ or higher




OK

6.REPLACE PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE PARKING ASSIST ECU
a.

Replace the parking assist ECU with a new or known good one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY