Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › from 2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Speaker Circuit  


DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.


WIRING DIAGRAM

E305083E02
0.396,0.76 2.625,0.958 2.229,0.198 10 false Front No. 1 Speaker Assembly RH 0.396,0.604 0.646,0.802 0.25,0.198 10 false N1 2.76,0.479 2.854,0.677 0.094,0.198 10 false 1 2.76,1.042 2.854,1.24 0.094,0.198 10 false 2 2.76,1.604 2.854,1.802 0.094,0.198 10 false 1 2.781,2.146 2.875,2.344 0.094,0.198 10 false 2 2.76,2.688 2.854,2.885 0.094,0.198 10 false 1 2.771,3.26 2.865,3.458 0.094,0.198 10 false 2 2.76,3.813 2.854,4.01 0.094,0.198 10 false 1 2.771,4.396 2.865,4.594 0.094,0.198 10 false 2 0.375,1.854 2.604,2.052 2.229,0.198 10 false Front No. 1 Speaker Assembly LH 0.375,1.698 0.625,1.896 0.25,0.198 10 false O1 0.417,2.969 2.646,3.167 2.229,0.198 10 false Front No. 2 Speaker Assembly RH 0.417,2.813 0.667,3.01 0.25,0.198 10 false I6 0.417,4.083 2.646,4.281 2.229,0.198 10 false Front No. 2 Speaker Assembly LH 0.417,3.917 0.719,4.115 0.302,0.198 10 false I7 5.969,0.438 6.396,0.604 0.427,0.167 10 false WFR+ 5.969,1.083 6.396,1.25 0.427,0.167 10 false WFR- 5.708,0.344 5.917,0.51 0.208,0.167 10 false 15 5.708,0.969 5.917,1.135 0.208,0.167 10 false 30 5.792,1.448 6,1.615 0.208,0.167 10 false 8 5.708,2.083 5.917,2.25 0.208,0.167 10 false 23 5.708,3.198 5.917,3.365 0.208,0.167 10 false 24 5.708,4.302 5.917,4.469 0.208,0.167 10 false 29 5.708,3.667 5.917,3.833 0.208,0.167 10 false 14 5.792,2.563 6,2.729 0.208,0.167 10 false 9 5.969,1.573 6.396,1.74 0.427,0.167 10 false WFL+ 5.969,2.208 6.396,2.375 0.427,0.167 10 false WFL- 5.969,2.698 6.396,2.865 0.427,0.167 10 false FR+ 5.969,3.323 6.396,3.49 0.427,0.167 10 false FR- 5.969,3.792 6.396,3.958 0.427,0.167 10 false FL+ 5.969,4.438 6.396,4.604 0.427,0.167 10 false FL- 5.781,4.979 6.208,5.146 0.427,0.167 10 false L30 5.781,5.146 7.021,5.635 1.24,0.49 10 false Stereo Component Amplifier Assembly

E305084E02
0.854,1.031 3.083,1.229 2.229,0.198 10 false Rear Speaker Assembly RH 0.854,0.875 1.156,1.073 0.302,0.198 10 false P3 2.76,0.76 2.854,0.958 0.094,0.198 10 false 1 2.75,1.313 2.844,1.51 0.094,0.198 10 false 2 5.708,0.615 5.917,0.781 0.208,0.167 10 false 12 5.708,1.26 5.917,1.427 0.208,0.167 10 false 27 5.969,0.729 6.396,0.896 0.427,0.167 10 false RR+ 5.969,1.354 6.396,1.521 0.427,0.167 10 false RR- 0.854,2.146 2.729,2.333 1.875,0.188 10 false Rear Speaker Assembly LH 0.854,1.979 1.26,2.167 0.406,0.188 10 false Q3 2.76,1.875 2.854,2.063 0.094,0.188 10 false 1 2.771,2.427 2.865,2.615 0.094,0.188 10 false 2 0.5,3.25 2.698,3.438 2.198,0.188 10 false Rear No. 2 Speaker Assembly RH 0.5,3.083 0.906,3.271 0.406,0.188 10 false P5 2.76,2.99 2.854,3.177 0.094,0.188 10 false 2 2.771,3.542 2.865,3.729 0.094,0.188 10 false 1 0.469,4.344 2.667,4.531 2.198,0.188 10 false Rear No. 2 Speaker Assembly LH 0.458,4.177 0.865,4.365 0.406,0.188 10 false Q5 2.76,4.094 2.854,4.281 0.094,0.188 10 false 2 2.76,4.646 2.854,4.833 0.094,0.188 10 false 1 5.729,1.729 5.917,1.917 0.188,0.188 10 false 11 5.719,2.365 5.896,2.552 0.177,0.188 10 false 26 5.719,2.844 5.896,3.031 0.177,0.188 10 false 13 5.719,3.458 5.896,3.646 0.177,0.188 10 false 28 5.719,3.948 5.896,4.135 0.177,0.188 10 false 10 5.719,4.573 5.896,4.76 0.177,0.188 10 false 25 5.979,1.844 6.563,2.031 0.583,0.188 10 false RL+ 5.979,2.469 6.563,2.656 0.583,0.188 10 false RL- 5.969,2.958 6.552,3.146 0.583,0.188 10 false TWR+ 5.969,3.594 6.552,3.781 0.583,0.188 10 false TWR- 5.969,4.063 6.552,4.25 0.583,0.188 10 false TWL+ 5.969,4.719 6.552,4.906 0.583,0.188 10 false TWL- 5.781,5.135 6.365,5.323 0.583,0.188 10 false L30 5.781,5.302 7.042,5.865 1.26,0.563 10 false Stereo Component Amplifier Assembly

PROCEDURE

1.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen.

Refer to Check Speaker in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>OPERATION CHECK).


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly A
Front No. 2 speaker assembly B
Rear speaker assembly C
Rear No. 2 speaker assembly D


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)

B

4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

C

6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)

D

8.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
a.

Disconnect the L30 stereo component amplifier assembly connector.


b.

Disconnect the N1 and O1 front No. 1 speaker assembly connectors.


c.

Measure the resistance between the stereo component amplifier assembly and each of the front No. 1 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-15 (WFR+) - N1-1 Always Below 1 Ω
L30-30 (WFR-) - N1-2 Always Below 1 Ω
L30-8 (WFL+) - O1-1 Always Below 1 Ω
L30-23 (WFL-) - O1-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-15 (WFR+) - Body ground Always 10 kΩ or higher
L30-30 (WFR-) - Body ground Always 10 kΩ or higher
L30-8 (WFL+) - Body ground Always 10 kΩ or higher
L30-23 (WFL-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).


b.
E289435E05
0.155,0 0.602,0.448 0.448,0.448 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 4.6 to 6.6 Ω


Text in Illustration
*a Component without harness connected
(Front No. 1 Speaker Assembly)



OK

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the L30 stereo component amplifier assembly connector.


b.

Disconnect the I6 and I7 front No. 2 speaker assembly connectors.


c.

Measure the resistance between the stereo component amplifier assembly and each of the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-9 (FR+) - I6-1 Always Below 1 Ω
L30-24 (FR-) - I6-2 Always Below 1 Ω
L30-14 (FL+) - I7-1 Always Below 1 Ω
L30-29 (FL-) - I7-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-9 (FR+) - Body ground Always 10 kΩ or higher
L30-24 (FR-) - Body ground Always 10 kΩ or higher
L30-14 (FL+) - Body ground Always 10 kΩ or higher
L30-29 (FL-) - Body ground Always 10 kΩ or higher




OK

5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).


b.
E187205E17
0.154,0.034 0.341,0.249 0.187,0.215 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω


Text in Illustration
*a Component without harness connected
(Front No. 2 Speaker Assembly)



OK

NG

6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the L30 stereo component amplifier assembly connector.


b.

Disconnect the P3 and Q3 rear speaker assembly connectors.


c.

Measure the resistance between the stereo component amplifier assembly and each of the rear speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-12 (RR+) - P3-1 Always Below 1 Ω
L30-27 (RR-) - P3-2 Always Below 1 Ω
L30-11 (RL+) - Q3-1 Always Below 1 Ω
L30-26 (RL-) - Q3-2 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-12 (RR+) - Body ground Always 10 kΩ or higher
L30-27 (RR-) - Body ground Always 10 kΩ or higher
L30-11 (RL+) - Body ground Always 10 kΩ or higher
L30-26 (RL-) - Body ground Always 10 kΩ or higher




OK

7.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR SPEAKER ASSEMBLY
a.

Remove the rear speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).


b.
E289435E02
0.155,0 0.602,0.448 0.448,0.448 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 5.2 Ω


Text in Illustration
*a Component without harness connected
(Rear Speaker Assembly)



OK

NG

8.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the L30 stereo component amplifier assembly connector.


b.

Disconnect the P5 and Q5 rear No. 2 speaker assembly connectors.


c.

Measure the resistance between the stereo component amplifier assembly and each of the rear No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-13 (TWR+) - P5-2 Always Below 1 Ω
L30-28 (TWR-) - P5-1 Always Below 1 Ω
L30-10 (TWL+) - Q5-2 Always Below 1 Ω
L30-25 (TWL-) - Q5-1 Always Below 1 Ω



d.

Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-13 (TWR+) - Body ground Always 10 kΩ or higher
L30-28 (TWR-) - Body ground Always 10 kΩ or higher
L30-10 (TWL+) - Body ground Always 10 kΩ or higher
L30-25 (TWL-) - Body ground Always 10 kΩ or higher




OK

9.INSPECT REAR NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT REAR NO. 2 SPEAKER ASSEMBLY
a.

Remove the rear No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).


b.
E177897E92
0.182,0.133 0.380,0.303 0.198,0.170 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 3.2 to 4.8 Ω


Text in Illustration
*a Component without harness connected
(Rear No. 2 Speaker Assembly)



OK

NG

REPLACE REAR NO. 2 SPEAKER ASSEMBLY