Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM C

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the parking assist ECU receives a signal via CAN communication from the spiral cable with sensor sub-assembly that indicates a power supply system problem.

DTC No. DTC Detection Condition Trouble Area
C1625 Open or short in steering angle sensor +B
·

Harness or connector

·

Steering angle sensor (spiral cable with sensor sub-assembly)



WIRING DIAGRAM

E224380E18
1.117,3.211 2.864,3.386 1.747,0.175 10 : CAN Communication Line 3.246,0.62 3.604,0.794 0.358,0.174 10 BAT 3.246,1.73 3.576,1.905 0.330,0.174 10 ESS 5.37,2.331 6.675,2.505 1.305,0.174 10 Parking Assist ECU 2.243,0.767 2.714,0.941 0.471,0.174 10 ECU-B 1.986,1.333 3.001,1.508 1.014,0.174 10 ECU-IG NO. 2 0.773,1.168 1.763,1.523 0.990,0.355 10 from IG1 NO. 1 Relay 0.389,0.598 1.729,0.772 1.340,0.174 10 from Auxiliary Battery 3.058,2.359 4.643,2.775 1.585,0.416 10 Spiral Cable with Sensor Sub-assembly 3.053,0.526 3.176,0.701 0.123,0.174 10 6 3.053,1.069 3.176,1.244 0.123,0.174 10 5 3.053,1.623 3.176,1.797 0.123,0.174 10 2 3.246,1.177 3.410,1.351 0.164,0.174 10 IG 5.359,2.165 5.700,2.340 0.341,0.174 10 L65 3.069,2.193 3.408,2.368 0.339,0.174 10 L51

CAUTION / NOTICE / HINT

NOTICE:
·

When the "System initializing" message is displayed on the radio and display receiver assembly*1 or navigation receiver assembly*2 after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


*1: for Radio and Display Type

*2: for Navigation Receiver Type



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY POWER SUPPLY)
a.

Disconnect the L51 spiral cable with sensor sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L51-2 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L51-5 (IG) - L51-2 (ESS) Power switch on (IG) 11 to 14 V
L51-6 (BAT) - L51-2 (ESS) Power switch off 11 to 14 V




OK

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR