Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the SIGNAL CHECK screen, it is possible to check if the state of signals sent to the parking assist ECU is normal (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DIAGNOSIS SYSTEM).

HINT:
·

On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver
CAN CAN communication CAN communication condition DTC is output -
IPA SW Vehicle wire harness Parking assist pre support switch assembly signal input DTC is not output Parking assist pre support switch assembly
HT SENS Vehicle wire harness Height control sensor signal input DTC is output Rear height control sensor sub-assembly RH
HT INIT - Height control sensor vehicle height difference setting status DTC is output -

WIRING DIAGRAM

E236873E03
1.249,6.694 2.948,6.868 1.698,0.174 10 : CAN Communication Line 5.582,6.637 6.852,6.840 1.269,0.202 10 Parking Assist ECU 2.93,0.772 3.076,0.946 0.146,0.174 10 3 5.698,0.859 6.184,1.034 0.486,0.174 10 ISSW 1.17,3.21 1.461,3.384 0.291,0.174 10 S25 3.097,0.954 3.212,1.128 0.115,0.174 10 E 4.059,0.954 4.230,1.128 0.171,0.174 10 IG 2.832,4.433 4.569,4.796 1.736,0.363 10 Main Body ECU (Multiplex Network Body ECU) 2.352,1.284 2.612,1.455 0.260,0.171 10 L56 2.352,1.443 5.191,1.614 2.838,0.171 10 Parking Assist Pre Support Switch Assembly 1.17,3.383 4.107,3.715 2.938,0.332 10 Rear Height Control Sensor Sub-assembly RH 2.902,5.864 4.448,6.196 1.547,0.332 10 Spiral Cable with Sensor Sub-assembly 4.303,0.772 4.459,0.946 0.156,0.174 10 6 3.934,2.024 4.395,2.198 0.461,0.174 10 SHB 4.295,1.93 4.462,2.114 0.168,0.185 10 3 3.801,2.598 4.240,2.772 0.439,0.174 10 SHRR 4.295,2.502 4.451,2.676 0.156,0.174 10 2 3.896,2.94 4.229,3.114 0.333,0.174 10 SHG 4.295,2.849 4.451,3.023 0.156,0.174 10 1 5.439,0.768 5.640,0.943 0.201,0.174 10 26 5.698,2.014 6.335,2.188 0.636,0.174 10 HBL+*1 5.439,1.923 5.640,2.097 0.201,0.174 10 27 5.698,2.598 5.958,2.772 0.259,0.174 10 HI1 5.51,2.502 5.711,2.676 0.201,0.174 10 9 5.698,2.94 6.069,3.114 0.370,0.174 10 HG1 5.451,2.849 5.652,3.023 0.201,0.174 10 31 5.582,6.474 5.918,6.648 0.336,0.174 10 L65 5.444,2.23 5.646,2.405 0.201,0.174 10 30 5.698,2.333 6.335,2.507 0.636,0.174 10 HBE+*2 0.682,7.037 2.093,7.211 1.411,0.174 10 *1: for LED Headlight 0.682,7.341 2.385,7.516 1.703,0.174 10 *2: for Halogen Headlight

CAUTION / NOTICE / HINT

NOTICE:
·

When the "System initializing" message is displayed on the radio and display receiver assembly*1 or navigation receiver assembly*2 after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).


*1: for Radio and Display Type

*2: for Navigation Receiver Type



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E305121

Check which items display "CHK" (red) on the SIGNAL CHECK screen.

Result:
Result Proceed to
"IPA SW" displays "CHK" (red). A
"HT INIT" displays "CHK" (red). B
Both "HT SENS" and "HT INIT" display "CHK" (red). C
"CAN" displays "CHK" (red). C




A

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - PARKING ASSIST PRE SUPPORT SWITCH ASSEMBLY)

B

ADJUST HEIGHT CONTROL SENSOR VEHICLE HEIGHT DIFFERENCE SETTING

C

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - PARKING ASSIST PRE SUPPORT SWITCH ASSEMBLY)
a.

Disconnect the L65 parking assist ECU connector.


b.

Disconnect the L56 parking assist pre support switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-26 (ISSW) - L56-6 (IG) Always Below 1 Ω




OK

3.INSPECT PARKING ASSIST PRE SUPPORT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING ASSIST PRE SUPPORT SWITCH ASSEMBLY
a.

Remove the parking assist pre support switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST PRE SUPPORT SWITCH>REMOVAL).


b.
E361819E01
1.167,1.75 1.5,1.75 1.5,1.75 1.5,1.25 false 2.333,1.75 2,1.75 2,1.75 2,1.25 false 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.979,1.667 1.292,1.865 0.313,0.198 10 false IG 2.396,1.667 2.708,1.865 0.313,0.198 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (E) - 6 (IG) Parking assist pre support switch assembly pushed Below 1 Ω
Parking assist pre support switch assembly not pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Parking Assist Pre Support Switch Assembly)



OK

NG

REPLACE PARKING ASSIST PRE SUPPORT SWITCH ASSEMBLY