Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM D

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  DIAGNOSIS SYSTEM  


INTELLIGENT PARKING ASSIST OR DIAGNOSIS SYSTEM


a.

For intelligent parking assist system diagnosis, signals received by the parking assist ECU can be checked and the intelligent parking assist system can be calibrated, adjusted and checked using the radio and display receiver assembly*1 or navigation receiver assembly*2.

*1: for Radio and Display Type

*2: for Navigation Receiver Type


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).


HINT:

The displayed screens and items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (during parking assist ECU initialization)


E311670E02
2.875,0.896 4.792,1.375 1.917,0.479 10 false Start diagnosis mode referring to the navigation system. 0.146,0.063 1.042,0.333 0.896,0.271 12 false Example: 3.896,6.927 4.083,7.146 0.188,0.219 10 false or

E311253


DIAGNOSIS SCREEN TRANSITION (after parking assist ECU initialization)


E311669E02
0.156,0.052 1.24,0.323 1.083,0.271 12 false Example: 2.917,1.083 4.844,1.531 1.927,0.448 10 false Start diagnosis mode referring to the navigation system.

E311254E02
4.313,1.75 4.917,1.969 0.604,0.219 10 false or 3.958,3.177 4.563,3.396 0.604,0.219 10 false or

E311255E01
4.26,5.453 4.827,5.618 0.568,0.165 10 or 4.253,6.819 4.821,6.984 0.568,0.165 10 or 4.956,8.332 5.524,8.497 0.568,0.165 10 or


DIAGNOSTIC MODE



b.

Failure diagnosis


c.

System check (Check using the system check mode screen.)




SIGNAL CHECK (parking assist ECU input signal)


a.

Start diagnostic mode.


i.
E307240E01
0.006,0 0.722,0.202 0.716,0.202 10 Example:

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting" screen.


ii.
E307209E02
0.052,0.042 1.281,0.24 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.

HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.

Parking Assist ECU Initialization Screen Transition
Not performed SIGNAL CHECK screen
Performed MODE SETTING screen



iii.
E311252

When the screen changes to the "MODE SETTING" screen, select "BACK CAMERA SETTING" to display the "SIGNAL CHECK" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.
U191440E01
3.13,0.644 3.317,0.818 0.187,0.173 10 B 3.126,0.361 3.313,0.534 0.187,0.173 10 A

SIGNAL CHECK

i.

On the "SIGNAL CHECK" screen, the following are possible:

·

Inspection of the state of signals sent to the parking assist ECU.

·

Confirmation of the state of the height control sensor vehicle height difference setting.

·

Adjustment of the parking position for parallel parking mode.


Item Inspection Detail Note
CAN CAN communication status When "CHK" (red) is displayed, selecting "NEXT" will not change to the next screen.
IPA SW Parking assist pre support switch signal input
HT SENS Height control sensor signal input
HT INIT Vehicle height difference setting status

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "NEXT".

·

Select the following buttons to changes to the respective adjustment screen.

Button Transit Screen Adjustment Contents
A PARALLEL PARKING OFFSET Parking position for parallel parking mode
B HEIGHT SET Height control sensor vehicle height difference setting (See page (Click here))





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR).



d.

IPA SW inspection

i.

Check that "OK" (blue) is displayed for "IPA SW" and select "OK".


ii.

Check that "OK" (blue) changes to "CHK" (red). Press the parking assist pre support switch assembly and check that "CHK" (red) returns to "OK" (blue).

HINT:

If "CHK" (red) remains displayed or the "IPA SW" inspection result is not normal, perform troubleshooting according to Problem Symptoms Table ("CHK" message(s) are displayed on the "SIGNAL CHECK" screen) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>"CHK" message(s) are displayed on the SIGNAL CHECK screen.).




e.

HT SENS inspection

HINT:

If "CHK" (red) is displayed for "HT SENS", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR).



f.

HT INIT inspection

HINT:

If "CHK" (red) is displayed for "HT INIT", perform troubleshooting according to the table below.

Displayed Content Cause Troubleshooting
CHK
(red)
·

Vehicle height difference setting is not completed

·

Rear height control sensor sub-assembly RH is malfunctioning


·

If "CHK" (red) is also displayed for "HT INIT", check for DTCs and perform troubleshooting based on the output DTCs (See page (Click here)).

·

If "OK" (blue) is displayed for "HT INIT", perform vehicle height difference setting (See page (Click here)).







CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).



STEERING ANGLE SETTING (after parking assist ECU is initialized)


HINT:

If the vehicle width extension lines and predicted path lines are not aligned when the steering wheel is centered, or if the predicted path lines stop moving before the steering wheel is fully turned to either the left or right, adjust the steering angle settings.


a.

Center the steering wheel and stop the vehicle.


b.

Start diagnostic mode.


NOTICE:

The following must be carried out with the hybrid system started. Apply the parking brake, depress the brake pedal, push the P position switch, and ensure that the vehicle is not moving.


HINT:

The displayed items may differ depending on vehicle specifications.


i.
E307240E01
0.006,0 0.722,0.202 0.716,0.202 10 Example:

Select "Function Check/Setting" on the "Service Menu" screen.


ii.
E307209E02
0.052,0.042 1.281,0.24 1.229,0.198 10 false Example:

Select "Camera Setting I" on the "Function Check/Setting" screen.


iii.
E311252

Select "STEERING ANGLE SETTING" on the "MODE SETTING" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



iv.
E305121

Select "NEXT" on the "SIGNAL CHECK" screen.

NOTICE:
·

When "CHK" (red) is displayed for any items on the "SIGNAL CHECK" screen, selecting "NEXT" will not change the screen to the "STEERING ANGLE SETTING" screen.

·

When "CHK" is displayed for any items on the "SIGNAL CHECK" screen, perform inspections using the "SIGNAL CHECK" screen.





c.
E311257

Steering angle setting

i.

Check that the steering wheel is centered (approximately +/- 5 degrees or less) and select "STEERING CENTER MEMORIZE".


ii.

After the centered steering position is memorized, turn the steering wheel to the left and then to the right full lock positions and select "MAX STEERING ANGLE MEMORIZE".

HINT:

It is also possible to start by initially turning the steering wheel to the right side.



iii.

Select "MAX STEERING ANGLE MEMORIZE" to store the steering angle adjustment values and change the screen to the "MODE SETTING" screen.

HINT:
·

When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the steering angle adjustment values have been stored.

·

The adjustment values will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected.

·

The values are not stored until the beep has sounded.

·

When "BACK" is selected, the screen changes to "SIGNAL CHECK" without storing the set values.

·

If "OK" is selected without selecting "MAX STEERING ANGLE MEMORIZE", the values will not be stored (Change the screen to the "MODE SETTING" screen).

·

If the steering angle settings have not been adjusted, selecting "MAX STEERING ANGLE MEMORIZE" will not cause values to be stored.

·

Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the values to be stored if the steering sensor is malfunctioning.

·

If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the values to be stored after performing the steering angle setting procedure, replace the spiral cable with sensor sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).






e.

Confirm steering angle adjustment.

HINT:

If the steering angle setting procedure has been performed, confirm the steering angle adjustment using the intelligent parking assist screen after finishing diagnosis mode.


i.

Check on the intelligent parking assist screen that the predicted path line moves until the steering wheel is fully turned to either the left or right.

HINT:

If the predicted path line stops moving before the steering wheel is fully turned to either the left or right, the values have not been stored correctly. In this case, perform "STEERING CENTER MEMORIZE" and "MAX STEERING ANGLE MEMORIZE" again.





PARKING POSITION HORIZONTAL ADJUSTMENT FOR PARALLEL PARKING MODE


a.

Start diagnostic mode.


NOTICE:

The following must be carried out with the hybrid system started. Apply the parking brake, depress the brake pedal, push the P position switch, and ensure that the vehicle is not moving.


i.
E307240E01
0.006,0 0.722,0.202 0.716,0.202 10 Example:

Select "Function Check/Setting" on the "Service Menu" screen.


ii.
E307209E02
0.052,0.042 1.281,0.24 1.229,0.198 10 false Example:

Select "Camera Setting" on the "Function Check/Setting I" screen.


iii.
E311252

Select "BACK CAMERA SETTING" or "STEERING ANGLE SETTING" on the "MODE SETTING" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



iv.
E305121

Select "PARALLEL OFFSET" on the "SIGNAL CHECK" screen.



b.
E311258

PARALLEL PARKING OFFSET

HINT:

The "PARALLEL PARKING OFFSET" screen allows the parking position to be offset when the actual parking position deviates to the right or left of the set target parking position during parallel parking mode.


i.

Press "UP" or "DOWN" to adjust the parallel parking position horizontal offset amount.

E193120E05
1.917,3.063 1.74,3.354 false 2.302,3.063 2.479,3.354 false 4.479,3.052 4.292,3.333 false 4.865,3.063 5.052,3.344 false 0.073,0.094 1.896,0.458 1.823,0.365 10 false When parking parallel to edge of road on the left side: 3.563,0.083 5.406,0.458 1.844,0.375 10 false When parking parallel to edge of road on the right side: 0.313,1.698 1.188,1.99 0.875,0.292 10 false Edge of Road 5.594,1.708 6.469,2 0.875,0.292 10 false Edge of Road 1.552,0.708 2.719,1 1.167,0.292 10 false Vehicle Centerline 4.094,0.708 5.26,1 1.167,0.292 10 false Vehicle Centerline 2.938,1.854 3.938,2.146 1,0.292 10 false Center of Road 1.354,3.365 2.052,3.656 0.698,0.292 10 false + Direction 2.188,3.354 2.854,3.646 0.667,0.292 10 false - Direction 3.885,3.333 4.563,3.625 0.677,0.292 10 false - Direction 4.729,3.344 5.469,3.635 0.74,0.292 10 false + Direction

HINT:
·

Positive values are indicated in green and negative values are indicated in red.

·

The + direction indicates an offset toward the edge of the road, the - direction indicates an offset toward the center of the road.

·

When the value is shown as "10 CM" in red, it means -10 cm (the parking position is offset 10 cm towards the center of the road).

·

Available setting range: +20 cm to -40 cm (can be adjusted in 1 cm increments)




ii.

When "OK" is selected, the screen switches to the signal connection screen and a set value is stored.

·

When "OK" is selected, the value is stored after a beep sounds for confirmation.

·

The value will not be stored unless "OK" is selected.

·

The value is not stored until the beep has sounded.

·

When "BACK" is selected, the screen switches to the signal connection screen without storing the value (value entered is not stored).