Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2013.08–2014.11
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  Image from Camera for Intelligent Parking Assist is Abnormal  


DESCRIPTION

The display signal from the rear television camera assembly is transmitted to the navigation ECU sub-assembly via the parking assist ECU.

WIRING DIAGRAM

E222959E07
0.819,3.091 1.150,3.262 0.332,0.171 10 CV- 0.819,2.464 1.150,2.636 0.332,0.171 10 CV+ 0.819,3.729 1.150,3.900 0.332,0.171 10 CB+ 6.124,3.105 6.456,3.276 0.332,0.171 10 CV- 6.124,2.479 6.589,2.650 0.465,0.171 10 CV+ 6.12,4.372 6.569,4.544 0.449,0.171 10 CGND 0.36,5.773 1.561,6.121 1.200,0.348 10 Rear Television Camera Assembly 2.557,6.324 4.461,6.489 1.904,0.165 10 : Digital Communication Cable 3.205,5.773 4.037,5.945 0.832,0.171 10 *1: Shielded 0.36,5.622 0.663,5.793 0.303,0.171 10 V6 0.234,1.407 1.641,1.755 1.406,0.348 10 Navigation ECU Sub-assembly 0.234,1.244 0.593,1.415 0.359,0.171 10 L137 2.399,4.506 2.583,4.677 0.184,0.171 10 *1 3.407,4.506 3.592,4.677 0.184,0.171 10 *1 4.43,4.506 4.614,4.677 0.184,0.171 10 *1 5.798,5.603 7.061,5.794 1.264,0.191 10 Parking Assist ECU 6.124,3.745 6.456,3.916 0.332,0.171 10 CB+ 1.195,3.004 1.327,3.175 0.132,0.171 10 1 1.195,2.379 1.327,2.550 0.132,0.171 10 2 0.766,0.692 1.150,0.863 0.384,0.171 10 GVIF 6.124,0.692 6.508,0.863 0.384,0.171 10 GVIF 1.195,0.607 1.327,0.778 0.132,0.171 10 1 1.195,3.645 1.327,3.816 0.132,0.171 10 4 0.683,4.372 1.149,4.543 0.466,0.171 10 CGND 1.195,4.288 1.327,4.459 0.132,0.171 10 3 5.794,2.92 5.997,3.091 0.203,0.171 10 38 5.793,2.284 5.981,2.455 0.189,0.171 10 15 5.793,4.18 5.981,4.351 0.189,0.171 10 37 6.12,5.003 6.536,5.174 0.416,0.171 10 GND1 5.842,4.811 5.954,4.982 0.112,0.171 10 4 5.793,3.551 5.981,3.722 0.189,0.171 10 14 5.733,3.107 6.062,3.278 0.329,0.171 10 L65 5.733,2.483 6.062,2.654 0.329,0.171 10 L65 5.835,0.535 5.938,0.706 0.103,0.171 10 1 5.702,0.722 6.032,0.893 0.330,0.171 10 L136 5.733,3.742 6.062,3.913 0.329,0.171 10 L65 5.733,4.372 6.062,4.543 0.329,0.171 10 L65 5.733,5.007 6.062,5.179 0.329,0.171 10 L64

CAUTION / NOTICE / HINT

NOTICE:
·

When the "System initializing" message is displayed on the navigation ECU sub-assembly after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).



HINT:

Images are difficult to discern even in normal conditions if:

·

Electrical devices are used in the cabin (noise may occur in the image).

·

Accessories that generate radio waves have been installed (noise may occur in the image).

·

The outer mirror switch assembly is operated (noise may occur in the image).

·

The camera screen is frosted over (the image immediately after turning the power switch on (IG) may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The ambient light around the camera is too bright. (When a strong light, such as a sunbeam reflected off the vehicle body, hits the camera, the image may be blurred. This is called the "SMEAR" phenomenon, peculiar to the CCD camera.)

·

The rear television camera assembly lens is scratched.

·

The rear television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)

OK

2.CHECK PARKING ASSIST ECU (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CV-, CGND)

OK

3.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - POWER SOURCE)

NG

3.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - POWER SOURCE)

OK

4.CHECK PARKING ASSIST ECU (CV+, GND1)

NG

4.CHECK PARKING ASSIST ECU (CV+, GND1)

OK

5.READ VALUE USING GTS

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY

5.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / IPA/Parking Assist Monitor / Data List.


e.

Check the Data List for proper functioning of the following items.

IPA/Parking Assist Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ASIC Output Status Output condition of camera display/OK or NG OK: Output condition of camera display is normal
NG: Output condition of camera display is abnormal
-



OK

6.CHECK DIGITAL COMMUNICATION CABLE CONNECTOR

NG

6.CHECK DIGITAL COMMUNICATION CABLE CONNECTOR
a.

Check the digital communication cable connectors.

i.

Check the digital communication cable connectors between the parking assist ECU and navigation ECU sub-assembly for any connection problems (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



b.

Check if the same malfunction recurs when the intelligent parking assist screen is displayed.

Result:
Result Proceed to
Malfunction does not reoccur (returns to normal) A
Malfunction reoccurs B




A

END

B

7.REPLACE WIRE HARNESS (DIGITAL COMMUNICATION CABLE)
7.REPLACE WIRE HARNESS (DIGITAL COMMUNICATION CABLE)
a.

Replace the digital communication cable between the parking assist ECU and navigation ECU sub-assembly with a new one.


b.

Check if the same malfunction recurs when the intelligent parking assist screen is displayed.

Result:
Result Proceed to
Malfunction does not reoccur (returns to normal) A
Malfunction reoccurs B




A

END

B

8.REPLACE NAVIGATION ECU SUB-ASSEMBLY
8.REPLACE NAVIGATION ECU SUB-ASSEMBLY
a.

Replace the navigation ECU sub-assembly with a new or known good one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).


b.

Check if the same malfunction recurs when the intelligent parking assist screen is displayed.

Result:
Result Proceed to
Malfunction does not reoccur A
Malfunction reoccurs B




A

END

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE