Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2012.03–2013.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2321 No communication between power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for driver side)

·

Main body ECU (multiplex network body ECU)

·

Multiplex network master switch assembly

·

Wire harness or connector

·

D FR DOOR fuse



WIRING DIAGRAM

B228561E20
0.742,2.439 2.379,2.576 1.637,0.137 10 : LIN Communication Line 0.259,1.818 2.286,2.191 2.026,0.373 10 Instrument Panel Junction Block Assembly 0.502,1.008 2.142,1.316 1.640,0.309 10 Main Body ECU (Multiplex Network Body ECU) 0.955,0.538 1.282,0.676 0.327,0.137 10 LIN2 3.818,0.407 4.145,0.545 0.327,0.137 10 LIN2 3.239,0.407 3.566,0.545 0.327,0.137 10 LIN1 5.032,0.548 5.290,0.685 0.258,0.137 10 LIN 2.779,1.771 4.333,2.094 1.554,0.323 10 Multiplex Network Master Switch Assembly 0.259,1.687 0.480,1.834 0.221,0.147 10 2A 2.779,1.444 3.143,1.595 0.364,0.151 10 O6*1 2.779,1.612 3.202,1.764 0.423,0.151 10 N13*2 4.649,1.757 6.669,2.075 2.019,0.318 10 Power Window Regulator Motor Assembly (for Driver Side) 4.649,1.437 5.013,1.588 0.364,0.151 10 O2*1 4.649,1.605 4.994,1.757 0.344,0.151 10 N2*2 5.614,1.215 5.966,1.371 0.352,0.156 10 GND 5.803,0.562 5.931,0.717 0.128,0.156 10 B 6.204,0.692 7.013,0.848 0.809,0.156 10 D FR DOOR 5.978,0.424 6.111,0.589 0.133,0.165 10 2 5.978,1.117 6.111,1.282 0.133,0.165 10 1 2.991,0.389 3.177,0.545 0.186,0.156 10 17 4.192,0.389 4.378,0.545 0.186,0.156 10 16 4.868,0.403 4.998,0.559 0.130,0.156 10 9 2.258,0.403 2.433,0.545 0.174,0.142 10 27 1.338,0.403 1.513,0.545 0.174,0.142 10 16 0.505,0.858 0.762,1.000 0.258,0.142 10 MB 3.124,2.495 3.845,2.632 0.721,0.137 10 *1: for LHD 4.119,2.495 4.882,2.632 0.762,0.137 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Result:
Result Proceed to
Only DTC B2321 is output. A
DTC B1206 and B2321 are output simultaneously. B


HINT:

When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.




A

2.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE POWER WINDOW REGULATOR MOTOR)

B

2.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE POWER WINDOW REGULATOR MOTOR)
a.

Disconnect the O6*1 or N13*2 multiplex network master switch connector.


b.

Disconnect the O2*1 or N2*2 power window regulator motor (for driver side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O6-16 (LIN2) - O2-9 (LIN)*1
N13-16 (LIN2) - N2-9 (LIN)*2
Always Below 1 Ω
O6-16 (LIN2) - Body ground*1
N13-16 (LIN2) - Body ground*2
Always 10 kΩ or higher


*1: for LHD

*2: for RHD




OK

3.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.
B203350E04
0.614,1.567 0.814,1.764 0.200,0.198 10 *1 1.903,3.207 2.238,3.347 0.336,0.140 10 LIN2 1.005,3.207 1.326,3.347 0.322,0.140 10 LIN1 1.681,2.967 1.681,3.299 1.681,3.299 1.903,3.299 false 1.558,2.967 1.558,3.301 1.558,3.301 1.382,3.301 false

Remove the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 (LIN2) - 17 (LIN1) Always Below 1 Ω
16 (LIN2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Multiplex Network Master Switch Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)

NG

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)
a.
U190800E02
1.521,1.208 0.969,0.5 true 1.906,1.208 2.469,0.51 true 0.646,1.167 0.938,1.333 0.292,0.167 10 false O2 2.49,0.354 2.656,0.646 0.167,0.292 10 false B 0.646,0.385 1.042,0.656 0.396,0.271 10 false GND 0.583,0.063 0.781,0.24 0.198,0.177 10 false *1 0.656,1.458 0.938,1.833 0.281,0.375 10 false N2 0.99,1.156 1.219,1.396 0.229,0.24 10 false *2 0.99,1.438 1.167,1.646 0.177,0.208 10 false *3

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O2-2 (B) - Body ground*1
N2-2 (B) - Body ground*2
Power switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-1 (GND) - Body ground*1
N2-1 (GND) - Body ground*2
Always Below 1 Ω


*1: for LHD

*2: for RHD


Text in Illustration
*1 Front view of wire harness connector
(to Power Window Regulator Motor Assembly (for Driver Side))
*2 for LHD
*3 for RHD



OK

5.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE)
a.

Replace the power window regulator motor assembly (for driver side) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Front Door)>REMOVAL).



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT

b.

Check for DTCs.

OK:

DTC B2321 is not output.




OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)