Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2015.08–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) T

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  PROBLEM SYMPTOMS TABLE  


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).



Result List of How to Proceed with Troubleshooting
Symptom Suspected Area See page
The result of "How to Proceed with Troubleshooting" is "Open in CAN Main Bus Line". Open in CAN Main Bus Line (LHD Models) (Includes DLC3 branch lines and terminating resistors) (Click here)
Open in CAN Main Bus Line (RHD Models) (Includes DLC3 branch lines and terminating resistors) (Click here)
The result of "How to Proceed with Troubleshooting" is "Short in CAN Bus Lines". Short in CAN Bus Lines (LHD Models) (Click here)
Short in CAN Bus Lines (RHD Models) (Click here)
The result of "How to Proceed with Troubleshooting" is "Short to +B in CAN Bus Line". Short to +B in CAN Bus Line (LHD Models) (Click here)
Short to +B in CAN Bus Line (RHD Models) (Click here)
The result of "How to Proceed with Troubleshooting" is "Short to GND in CAN Bus Line". Short to GND in CAN Bus Line (LHD Models) (Click here)
Short to GND in CAN Bus Line (RHD Models) (Click here)
The result of "How to Proceed with Troubleshooting" is "Open in One Side of CAN Branch Line". Open in One Side of CAN Branch Line (Click here)

HINT:

Refer to How to Proceed with Troubleshooting for the V Bus Check procedure.


Communication Stop Mode Table
Symptom Suspected Area See page
"Skid Control (ABS/VSC/TRAC)" is not displayed on the GTS. Skid Control ECU Communication Stop Mode (Click here)
"Power Steering (EPS)" is not displayed on the GTS. Power Steering ECU Communication Stop Mode (Click here)
"Spiral cable (Steering Angle Sensor)" is not displayed on the GTS. Steering Angle Sensor Communication Stop Mode (Click here)
"Yaw Rate Sensor" is not displayed on the GTS. Yaw Rate Sensor Communication Stop Mode (Click here)
"ECM (Engine)" is not displayed on the GTS. ECM Communication Stop Mode (Click here)
"Transmission Control" is not displayed on the GTS. Transmission Control ECU Communication Stop Mode (Click here)
"Main Body" is not displayed on the GTS. Main Body ECU Communication Stop Mode (Click here)
"Hybrid Vehicle Control" and "Power Management1" are not displayed on the GTS. Power Management Control ECU Communication Stop Mode (Click here)
"Combination Meter" is not displayed on the GTS. Combination Meter ECU Communication Stop Mode (Click here)
"Certification (Smart)" is not displayed on the GTS. Certification ECU Communication Stop Mode (Click here)
"Airbag" is not displayed on the GTS. Center Airbag Sensor Communication Stop Mode (Click here)
"Display and Navigation (AVN1)" is not displayed on the GTS. Navigation ECU Communication Stop Mode (Click here)
"Display and Navigation (AVN1)" is not displayed on the GTS. Audio Receiver Assembly Communication Stop Mode (Click here)

DTC Combination Table
Symptom Suspected Area See page
Although CAN communication (V bus) is currently normal, ECUs connected to the V bus store CAN communication DTCs. The probable part for which communication is interrupted can be determined using DTC Combination Table and comparing the DTCs output from ECUs connected to the CAN communication system (Click here)