Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Main body ECU (multiplex network body ECU) branch line or connector

·

Power source circuit of main body ECU (multiplex network body ECU)

·

Main body ECU (multiplex network body ECU) ground circuit

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

C444449E01
0.5,1.104 3.406,1.302 2.906,0.198 10 false No. 1 CAN Junction Connector*1 0.146,1.26 0.573,1.51 0.427,0.25 10 false L133 1.531,0.229 1.792,0.479 0.26,0.25 10 false 5 1.521,0.75 1.781,1 0.26,0.25 10 false 11 5.198,0.125 5.521,0.375 0.323,0.25 10 false 14 5.198,0.646 5.521,0.896 0.323,0.25 10 false 13 5.125,0.323 5.479,0.604 0.354,0.281 10 false L201 5.552,0.333 6.073,0.604 0.521,0.271 10 false CANH 5.563,0.844 6.083,1.115 0.521,0.271 10 false CANL 4.146,2.042 5.167,2.406 1.021,0.365 10 false ECU-IG NO. 1 5.177,1.896 5.5,2.146 0.323,0.25 10 false MB 5.198,1.708 5.521,1.958 0.323,0.25 10 false 32 5.583,1.917 5.906,2.167 0.323,0.25 10 false IG 5.188,3.365 5.51,3.615 0.323,0.25 10 false MB 5.167,4.063 5.49,4.313 0.323,0.25 10 false MB 5.188,5.625 5.51,5.875 0.323,0.25 10 false MB 5.219,3.156 5.542,3.406 0.323,0.25 10 false 30 5.188,3.865 5.51,4.115 0.323,0.25 10 false 29 5.198,5.438 5.521,5.688 0.323,0.25 10 false 11 5.552,5.646 6.146,5.896 0.594,0.25 10 false GND1 5.573,4.073 6.167,4.323 0.594,0.25 10 false ACC 5.573,3.365 6.167,3.615 0.594,0.25 10 false BECU 3.427,2.656 4.094,2.917 0.667,0.26 10 false IG1 NO. 1 0.125,2.042 1.677,2.354 1.552,0.313 10 false from Auxiliary Battery 1.271,1.719 2.125,2 0.854,0.281 10 false DC/DC 0.094,2.531 1.917,2.99 1.823,0.458 10 false from Certification ECU (Smart Key ECU Assembly) 1.292,3.198 1.885,3.448 0.594,0.25 10 false ECU-B 2.271,1.906 2.625,2.156 0.354,0.25 10 false 2E*1 2.375,1.688 2.698,1.938 0.323,0.25 10 false 1 2.344,2.385 2.667,2.635 0.323,0.25 10 false 2B 2.365,2.188 2.688,2.438 0.323,0.25 10 false 25 2.354,3.354 2.677,3.604 0.323,0.25 10 false 2C 2.344,3.167 2.667,3.417 0.323,0.25 10 false 18 2.354,4.542 2.677,4.792 0.323,0.25 10 false 2A 2.344,4.333 2.667,4.583 0.323,0.25 10 false 43 3.615,4.813 4.01,5.021 0.396,0.208 10 false ACC 4.271,4.208 5.115,4.5 0.844,0.292 10 false ECU-ACC 2.365,5.094 2.688,5.344 0.323,0.25 10 false 2B 2.365,5.625 2.688,5.875 0.323,0.25 10 false 2B 2.406,4.896 2.729,5.146 0.323,0.25 10 false 4 2.396,5.427 2.719,5.677 0.323,0.25 10 false 6 2.156,5.979 3.75,6.531 1.594,0.552 10 false Instrument Panel Junction Block Assembly 5.292,6.052 6.927,6.604 1.635,0.552 10 false Main Body ECU (Multiplex Network Body ECU) 0.083,3.5 1.635,3.813 1.552,0.313 10 false from Auxiliary Battery 0.094,4.677 1.917,5.135 1.823,0.458 10 false from Certification ECU (Smart Key ECU Assembly) 5.125,0.844 5.479,1.125 0.354,0.281 10 false L201 0.146,1.104 0.573,1.354 0.427,0.25 10 false L132 0.5,1.271 3.406,1.469 2.906,0.198 10 false No. 3 CAN Junction Connector*2 0.396,5.917 2.083,6.115 1.688,0.198 10 false *1: for LHD 0.396,6.25 2.083,6.448 1.688,0.198 10 false *2: for RHD 2.74,1.906 3.094,2.156 0.354,0.25 10 false 2F*2 2.813,1.698 3.135,1.948 0.323,0.25 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L201 main body ECU (multiplex network body ECU) connector.


c.
U191004E03
2.417,0.792 2.323,0.792 2.323,0.792 2.031,1.76 false 2.427,0.344 2.271,0.344 2.271,0.344 1.885,1.771 false 0.146,0.125 0.469,0.51 0.323,0.385 10 false *a 1.563,2.698 2.031,2.958 0.469,0.26 10 false L201 2.49,0.719 2.958,1.031 0.469,0.313 10 false CANH 2.49,0.26 2.958,0.552 0.469,0.292 10 false CANL

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))

Standard Resistance:
Tester Connection Condition Specified Condition
L201-14 (CANH) - L201-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.
U191032E01
0.056,0.052 0.259,0.280 0.203,0.228 10 *a 0.418,0.559 0.831,0.722 0.413,0.163 10 GND1 2.111,0.614 2.423,0.777 0.311,0.163 10 ACC 2.411,0.227 2.844,0.369 0.433,0.142 10 BECU 2.917,1.634 3.083,1.774 0.165,0.140 10 IG 0.893,0.636 0.976,0.636 0.976,0.636 1.24,1.103 false 3.108,1.712 3.223,1.712 3.223,1.712 3.123,1.147 false 2.498,0.691 2.581,0.691 2.581,0.691 2.844,1.082 false 2.937,0.305 3.052,0.305 3.052,0.305 2.931,1.083 false 1.599,0.525 1.921,0.734 0.323,0.210 10 MB

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)

Standard Resistance:
Tester Connection Condition Specified Condition
MB-11 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


HINT:

Perform this inspection with the wire harness connected to the instrument panel junction block assembly.



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MB-30 (BECU) - Body ground Power switch off 11 to 14 V
MB-29 (ACC) - Body ground Power switch on (ACC) 11 to 14 V
MB-32 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result Proceed to
OK A
NG (BECU) B
NG (ACC) C
NG (IG) D
NG (GND1) E



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

3.CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT)

C

GO TO LIGHTING (INT) SYSTEM (ACC SIGNAL CIRCUIT)

D

GO TO LIGHTING (INT) SYSTEM (IG SIGNAL CIRCUIT)

E

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (BECU SIGNAL CIRCUIT)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the 2C instrument panel junction block assembly connector.


c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.
U191087E01
1.591,0.896 1.863,1.052 0.272,0.156 10 2C 1.441,2.2 1.894,2.356 0.453,0.156 10 BECU 0.284,0.226 0.557,0.382 0.272,0.156 10 *a 1.699,1.758 1.671,2.172 false

Measure the voltage according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)

Standard Voltage:
Tester Connection Condition Specified Condition
2C-18 (BECU) - Body ground Power switch off 11 to 14 V




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BECU SIGNAL CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the 2B instrument panel junction block assembly connector.


c.
U191086E01
1.7,0.458 1.896,0.611 0.196,0.153 10 2B 2.391,0.936 2.808,1.090 0.417,0.153 10 GND1 2.103,1.539 2.172,1.019 2.172,1.019 2.277,1.019 false 0.673,0.936 1.089,1.090 0.417,0.153 10 GND1 0.078,0.077 0.242,0.231 0.164,0.153 10 *a 1.51,1.539 1.379,1.019 1.379,1.019 1.177,1.019 false

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)

Standard Resistance:
Tester Connection Condition Specified Condition
2B-4 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
2B-6 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)