Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 3 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2

·

No. 6 CAN junction connector



·

*1: for Radio and Display Type

·

*2: for Navigation Receiver Type


WIRING DIAGRAM

C351110E09
1.438,1.208 1.75,1.406 0.313,0.198 10 false 21 1.438,0.74 1.75,0.938 0.313,0.198 10 false 6 3.677,0.729 3.99,0.927 0.313,0.198 10 false 1 3.688,1.198 4,1.396 0.313,0.198 10 false 4 4.76,2.771 5.073,2.969 0.313,0.198 10 false 3 5.771,3.25 6.083,3.448 0.313,0.198 10 false 10 4.75,3.26 5.063,3.458 0.313,0.198 10 false 6 3.667,4.865 3.979,5.063 0.313,0.198 10 false 2 1.417,4.854 1.729,5.052 0.313,0.198 10 false 19 3.677,5.323 3.99,5.521 0.313,0.198 10 false 5 1.427,5.333 1.74,5.531 0.313,0.198 10 false 20 0.917,0.74 1.333,0.958 0.417,0.219 10 false CA3H 0.938,1.229 1.354,1.448 0.417,0.219 10 false CA3L 0.344,1.083 0.76,1.302 0.417,0.219 10 false 120 Ω 0.885,4.875 1.344,5.073 0.458,0.198 10 false CAYH 0.927,5.354 1.385,5.552 0.458,0.198 10 false CAYL 0.344,5.198 0.76,5.417 0.417,0.219 10 false 120 Ω 5.833,2.771 6.146,2.969 0.313,0.198 10 false 9 6.083,2.885 6.563,3.125 0.479,0.24 10 false CANH 6.083,3.375 6.563,3.615 0.479,0.24 10 false CANL 3.177,5.844 3.604,6.063 0.427,0.219 10 false L200 3.552,5.844 5.979,6.125 2.427,0.281 10 false No. 6 CAN Junction Connector 0.083,5.875 0.802,6.135 0.719,0.26 10 false L192 0.448,5.875 1.969,6.313 1.521,0.438 10 false Central Gateway ECU (Network Gateway ECU) 5.406,3.823 5.76,4.031 0.354,0.208 10 false L35 4.958,0.448 7.156,0.771 2.198,0.323 10 false *1: for Radio and Display Type 4.958,0.854 7.156,1.177 2.198,0.323 10 false *2: for Navigation Receiver Type 5.719,3.823 7.052,4.375 1.333,0.552 10 false Radio and Display Receiver Assembly*1 5.719,4.49 6.927,5.01 1.208,0.521 10 false Navigation Receiver Assembly*2 5.406,4.49 5.76,4.698 0.354,0.208 10 false L38

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 30 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L200 No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

U191207E02
2.01,1.396 2.01,0.26 2.01,0.26 2.292,0.26 true 1.875,1.396 1.875,0.26 1.875,0.26 1.625,0.26 true 1.573,1.396 1.573,0.677 1.573,0.677 1.208,0.677 true 2.302,1.406 2.302,0.688 2.302,0.688 2.667,0.688 true 2.156,1.396 2.156,0.458 2.156,0.458 2.438,0.458 true 1.729,1.396 1.729,0.458 1.729,0.458 1.49,0.458 true 5.25,1.146 5.25,0.604 5.25,0.604 4.885,0.604 true 0.292,0.146 0.667,0.427 0.375,0.281 10 false *a 2.333,0.177 3.167,0.49 0.833,0.313 10 false CANL*b 0.656,0.604 1.49,0.917 0.833,0.313 10 false CANH*b 0.948,0.167 1.781,0.479 0.833,0.313 10 false CANH*c*d 0.906,0.365 1.74,0.677 0.833,0.313 10 false CANH*b 2.729,0.615 3.563,0.927 0.833,0.313 10 false CANL*c*d 2.51,0.375 3.344,0.688 0.833,0.313 10 false CANL*b 0.74,1.406 1.271,1.625 0.531,0.219 10 false L200 3.865,1.344 4.396,1.563 0.531,0.219 10 false L61 4.635,0.531 5.469,0.844 0.833,0.313 10 false CG 3.917,0.188 4.292,0.469 0.375,0.281 10 false *1

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Radio and Display Receiver Assembly
(for Radio and Display Type)
*d to Navigation Receiver Assembly
(for Navigation Receiver Type)

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L200-1 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
L200-4 (CANL) - L61-4 (CG)
L200-2 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
L200-5 (CANL) - L61-4 (CG)
L200-3 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Radio and display receiver assembly*1
L200-6 (CANL) - L61-4 (CG)
L200-3 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Navigation receiver assembly*2
L200-6 (CANL) - L61-4 (CG)


·

*1: for Radio and Display Type

·

*2: for Navigation Receiver Type


HINT:

If there is a short to ground in a CAN bus line without any CAN compatible optional devices connected to the option connector, repair or replace the CAN bus branch line or the option connector.


Result:
Symptom Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C




A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

U191208E02
1.573,1.396 1.573,0.677 1.573,0.677 1.208,0.677 true 2.146,1.406 2.146,0.688 2.146,0.688 2.521,0.688 true 2,1.396 2,0.458 2,0.458 2.281,0.458 true 1.729,1.406 1.729,0.469 1.729,0.469 1.49,0.469 true 5.25,1.135 5.25,0.708 5.25,0.708 4.885,0.708 true 0.115,0.063 0.49,0.344 0.375,0.281 10 false *a 2.354,0.375 3.188,0.688 0.833,0.313 10 false CANL*b 0.656,0.583 1.49,0.896 0.833,0.313 10 false CANH*b 0.938,0.385 1.771,0.698 0.833,0.313 10 false CANH*b 2.573,0.615 3.406,0.927 0.833,0.313 10 false CANL*b 0.74,1.396 1.271,1.615 0.531,0.219 10 false L200 3.875,1.333 4.406,1.552 0.531,0.219 10 false L61 4.604,0.635 5.438,0.948 0.833,0.313 10 false CG 3.729,0.094 4.104,0.375 0.375,0.281 10 false *1

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:
Tester Connection Condition Specified Condition
L200-1 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L200-4 (CANL) - L61-4 (CG)
L200-2 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L200-5 (CANL) - L61-4 (CG)




OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 6 CAN JUNCTION CONNECTOR)

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU).


c.

Measure the resistance according to the value(s) in the table below.

U191196E02
1.542,1.469 1.542,2.24 1.542,2.24 1.167,2.24 true 1.531,1.292 1.531,0.563 1.531,0.563 1.167,0.563 true 5.24,1.146 5.24,0.667 5.24,0.667 5.01,0.667 true 0.135,0.083 0.51,0.365 0.375,0.281 10 false *a 0.802,2.167 1.635,2.479 0.833,0.313 10 false CA3L 0.76,0.479 1.594,0.792 0.833,0.313 10 false CA3H 4.771,0.594 5.604,0.906 0.833,0.313 10 false CG 1.729,0.104 2.26,0.323 0.531,0.219 10 false L192 3.875,0.063 4.25,0.344 0.375,0.281 10 false *1 5.24,0.115 5.771,0.333 0.531,0.219 10 false L61

Text in Illustration
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -

Standard Resistance:
Tester Connection Condition Specified Condition
L192-6 (CA3H) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L192-21 (CA3L) - L61-4 (CG)


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR