There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus lines ·
Short in CAN branch lines ·
Central gateway ECU (network gateway ECU) ·
Hybrid vehicle control ECU ·
Driving support ECU assembly*1 ·
Lane departure warning camera*2 ·
Parking Assist ECU*3 ·
No. 4 CAN junction connector |
*1: w/ Pre-crash Safety System
*2: w/ Lane Departure Alert System
*3: w/ Intelligent Parking Assist System
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait at least approximately 33 seconds. Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and wait for approximately 52 seconds or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the L182, L183, L184, L185, L198 and L199 No. 4 CAN junction connectors.
Measure the resistance according to the value(s) in the table below.
Distinguish between the connectors connected to the No. 4 CAN junction connector by checking the color of the communication wire.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *a | Vehicle wire harness connector connected to CAN junction connector | *b | Rear view of wire harness connector
(to No. 4 CAN Junction Connector) |
| Tester Connection | Wiring Color | Condition | Specified Condition | Connected to |
|---|---|---|---|---|
| L199-1 (CANH) - L199-2 (CANL) | B - P | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| L198-1 (CANH) - L198-2 (CANL) | B - V | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| L185-1 (CANH) - L185-2 (CANL) | B - W | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Lane departure warning camera*1 |
| L184-1 (CANH) - L184-2 (CANL) | B - G | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Hybrid vehicle control ECU |
| L183-1 (CANH) - L183-2 (CANL) | B - L | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Parking assist ECU*2 |
| L182-1 (CANH) - L182-2 (CANL) | B - R | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Driving support ECU assembly*3 |
*1: w/ Lane Departure Alert System
*2: w/ Intelligent Parking Assist System
*3: w/ Pre-crash Safety System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Disconnect the L192 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
Distinguish between the connectors connected to the No. 4 CAN junction connector by checking the color of the communication wire.
Before disconnecting the connectors, make a note of where it is connected.
Reconnect the connector to its original position.
| *a | Vehicle wire harness connector connected to CAN junction connector | *b | Rear view of wire harness connector
(to No. 4 CAN Junction Connector) |
| Tester Connection | Wiring Color | Condition | Specified Condition |
|---|---|---|---|
| L198-1 (CANH) - L198-2 (CANL) | B - V | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| L199-1 (CANH) - L199-2 (CANL) | B - P | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU).
Measure the resistance according to the value(s) in the table below.
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L192-15 (CA5H) - L192-16 (CA5L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.
OK
NG