Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 5 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Hybrid vehicle control ECU

·

Driving support ECU assembly*1

·

Lane departure warning camera*2

·

Parking Assist ECU*3

·

No. 4 CAN junction connector



·

*1: w/ Pre-crash Safety System

·

*2: w/ Lane Departure Alert System

·

*3: w/ Intelligent Parking Assist System


WIRING DIAGRAM

C354533E02
0.438,7.313 1.927,7.813 1.49,0.5 10 false Central Gateway ECU (Network Gateway ECU) 0.073,7.313 0.448,7.563 0.375,0.25 10 false L192 0.354,6.667 0.927,6.938 0.573,0.271 10 false 120 Ω 0.313,0.875 0.885,1.146 0.573,0.271 10 false 120 Ω 0.875,6.344 1.448,6.615 0.573,0.271 10 false CAXH 0.896,6.823 1.469,7.094 0.573,0.271 10 false CAXL 1.365,6.823 1.938,7.094 0.573,0.271 10 false 24 1.354,6.344 1.927,6.615 0.573,0.271 10 false 9 4.656,4.865 5.229,5.135 0.573,0.271 10 false L199 4.656,4.385 5.229,4.656 0.573,0.271 10 false L199 4.75,4.219 5.323,4.49 0.573,0.271 10 false 1 4.76,4.677 5.333,4.948 0.573,0.271 10 false 2 0.885,0.552 1.458,0.823 0.573,0.271 10 false CA5H 0.906,1.031 1.479,1.302 0.573,0.271 10 false CA5L 1.333,0.552 1.906,0.823 0.573,0.271 10 false 15 1.333,1.042 1.906,1.313 0.573,0.271 10 false 16 3.448,0.646 4.021,0.917 0.573,0.271 10 false L198 3.438,1.115 4.01,1.385 0.573,0.271 10 false L198 3.573,0.469 4.146,0.74 0.573,0.271 10 false 1 4.771,0.479 5.344,0.75 0.573,0.271 10 false 1 4.771,2.25 5.344,2.521 0.573,0.271 10 false 1 3.552,2.25 4.125,2.521 0.573,0.271 10 false 1 3.542,4.188 4.115,4.458 0.573,0.271 10 false 1 3.552,4.688 4.125,4.958 0.573,0.271 10 false 2 3.542,2.729 4.115,3 0.573,0.271 10 false 2 4.781,2.75 5.354,3.021 0.573,0.271 10 false 2 4.771,0.958 5.344,1.229 0.573,0.271 10 false 2 3.563,0.948 4.135,1.219 0.573,0.271 10 false 2 4.656,2.438 5.229,2.708 0.573,0.271 10 false L184 4.656,2.917 5.229,3.188 0.573,0.271 10 false L184 5.979,3.375 6.875,3.885 0.896,0.51 10 false Hybrid Vehicle Control ECU 5.74,3.375 6.313,3.646 0.573,0.271 10 false L5 5.563,1.563 7.063,2.135 1.5,0.573 10 false Lane Departure Warning Camera*1 5.25,1.563 5.823,1.833 0.573,0.271 10 false U13 4.646,0.646 5.219,0.917 0.573,0.271 10 false L185 4.656,1.125 5.229,1.396 0.573,0.271 10 false L185 6.021,0.667 6.594,0.938 0.573,0.271 10 false CA1P 6.021,1.135 6.594,1.406 0.573,0.271 10 false CA1N 5.813,0.552 6.385,0.823 0.573,0.271 10 false 6 5.76,1.031 6.333,1.302 0.573,0.271 10 false 12 6.031,2.458 6.604,2.729 0.573,0.271 10 false CA2H 6.031,2.927 6.604,3.198 0.573,0.271 10 false CA2L 5.771,2.823 6.344,3.094 0.573,0.271 10 false 35 5.771,2.354 6.344,2.625 0.573,0.271 10 false 34 3.438,2.427 4.01,2.698 0.573,0.271 10 false L182 3.438,2.896 4.01,3.167 0.573,0.271 10 false L182 2.646,2.354 3.219,2.625 0.573,0.271 10 false 39 2.646,2.813 3.219,3.083 0.573,0.271 10 false 17 2.167,2.438 2.74,2.708 0.573,0.271 10 false CA2H 2.198,2.927 2.771,3.198 0.573,0.271 10 false CA2L 1.417,3.354 1.99,3.625 0.573,0.271 10 false L60 1.708,3.354 2.979,3.917 1.271,0.563 10 false Driving Support ECU Assembly*2 1.667,5.271 3.094,5.802 1.427,0.531 10 false Parking Assist ECU*3 1.365,5.271 1.938,5.542 0.573,0.271 10 false L65 3.448,4.385 4.021,4.656 0.573,0.271 10 false L183 3.438,4.865 4.01,5.135 0.573,0.271 10 false L183 2.156,4.385 2.729,4.656 0.573,0.271 10 false CANH 2.188,4.854 2.76,5.125 0.573,0.271 10 false CANL 2.625,4.302 3.198,4.573 0.573,0.271 10 false 40 2.625,4.781 3.198,5.052 0.573,0.271 10 false 39 3.635,5.302 4.844,5.823 1.208,0.521 10 false No. 4 CAN Junction Connector 3.344,7.281 7.156,7.604 3.813,0.323 10 false *1: w/ Lane Departure Alert System 3.344,7.656 7.156,7.979 3.813,0.323 10 false *2: w/ Pre-crash Safety System 3.344,8.042 7.156,8.365 3.813,0.323 10 false *3: w/ Intelligent Parking Assist System

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 33 seconds. Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and wait for approximately 52 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L182, L183, L184, L185, L198 and L199 No. 4 CAN junction connectors.


c.

Measure the resistance according to the value(s) in the table below.

HINT:
·

Distinguish between the connectors connected to the No. 4 CAN junction connector by checking the color of the communication wire.

·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C421483C30
5.667,0.583 6.083,0.833 0.417,0.25 0.75,1.667 0.917,1.833 0.917,1.833 1.083,1.833 true 0.719,1.49 0.917,1.25 0.917,1.25 1.083,1.25 true 6.375,1.833 6.177,2.26 6.177,2.26 6,2.26 true 1.781,0.896 2.094,1.094 0.313,0.198 10 false *b 0.458,0.969 0.771,1.167 0.313,0.198 10 false *a 5.74,0.635 6.344,0.844 0.604,0.208 10 false L61 1.188,1.177 1.698,1.385 0.51,0.208 10 false CANL 4.927,0.917 5.24,1.115 0.313,0.198 10 false *1 1.167,1.75 1.677,1.958 0.51,0.208 10 false CANH 5.677,2.188 6.281,2.396 0.604,0.208 10 false BAT
*1 DLC3 - -
*a Vehicle wire harness connector connected to CAN junction connector *b Rear view of wire harness connector
(to No. 4 CAN Junction Connector)


Standard Resistance:
Tester Connection Wiring Color Condition Specified Condition Connected to
L199-1 (CANH) - L61-16 (BAT) B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
L199-2 (CANL) - L61-16 (BAT) P
L198-1 (CANH) - L61-16 (BAT) B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
L198-2 (CANL) - L61-16 (BAT) V
L185-1 (CANH) - L61-16 (BAT) B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Forward recognition camera*1
L185-2 (CANL) - L61-16 (BAT) W
L184-1 (CANH) - L61-16 (BAT) B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Hybrid vehicle control ECU
L184-2 (CANL) - L61-16 (BAT) G
L183-1 (CANH) - L61-16 (BAT) B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Parking assist ECU*2
L183-2 (CANL) - L61-16 (BAT) L
L182-1 (CANH) - L61-16 (BAT) B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Driving support ECU assembly*3
L182-2 (CANL) - L61-16 (BAT) R


·

*1: w/ Lane Departure Alert System

·

*2: w/ Intelligent Parking Assist System

·

*3: w/ Pre-crash Safety System


Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C




A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

C

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)
a.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:
·

Distinguish between the connectors connected to the No. 4 CAN junction connector by checking the color of the communication wire.

·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C421483C30
5.667,0.583 6.083,0.833 0.417,0.25 0.75,1.667 0.917,1.833 0.917,1.833 1.083,1.833 true 0.719,1.49 0.917,1.25 0.917,1.25 1.083,1.25 true 6.375,1.833 6.177,2.26 6.177,2.26 6,2.26 true 1.781,0.896 2.094,1.094 0.313,0.198 10 false *b 0.458,0.969 0.771,1.167 0.313,0.198 10 false *a 5.74,0.635 6.344,0.844 0.604,0.208 10 false L61 1.188,1.177 1.698,1.385 0.51,0.208 10 false CANL 4.927,0.917 5.24,1.115 0.313,0.198 10 false *1 1.167,1.75 1.677,1.958 0.51,0.208 10 false CANH 5.677,2.188 6.281,2.396 0.604,0.208 10 false BAT
*1 DLC3 - -
*a Vehicle wire harness connector connected to CAN junction connector *b Rear view of wire harness connector
(to No. 4 CAN Junction Connector)


Standard Resistance:
Tester Connection Wiring Color Condition Specified Condition
L199-1 (CANH) - L61-16 (BAT) B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L199-2 (CANL) - L61-16 (BAT) P
L198-1 (CANH) - L61-16 (BAT) B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L198-2 (CANL) - L61-16 (BAT) V




OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU).


c.

Measure the resistance according to the value(s) in the table below.

U191197E02
2.146,1.406 2.146,0.688 2.146,0.688 2.479,0.688 true 2.052,1.406 2.052,0.688 2.052,0.688 1.677,0.688 true 5.948,1.719 5.948,2.177 5.948,2.177 5.719,2.177 true 0.135,0.146 0.51,0.427 0.375,0.281 10 false *a 1.302,0.615 2.135,0.927 0.833,0.313 10 false CA5L 2.521,0.615 3.354,0.927 0.833,0.313 10 false CA5H 5.417,2.104 6.25,2.417 0.833,0.313 10 false BAT 1.729,0.115 2.26,0.333 0.531,0.219 10 false L192 3.875,0.135 4.25,0.417 0.375,0.281 10 false *1 5.24,0.115 5.771,0.333 0.531,0.219 10 false L61

Text in Illustration
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -

Standard Resistance:
Tester Connection Condition Specified Condition
L192-15 (CA5H) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L192-16 (CA5L) - L61-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.





OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR