Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2013.08–2014.11
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2282  Vehicle Speed Signal Malfunction  


DESCRIPTION

This DTC is stored when a mismatch between the vehicle speed signal from the direct line sent by the combination meter sub-assembly and the vehicle speed signal sent via CAN communication is detected.

HINT:
·

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2282 Mismatch between the vehicle speed signal from the direct line sent by the combination meter sub-assembly and the vehicle speed signal sent via CAN communication (1-trip detection logic*).
·

CAN communication system

·

Combination meter sub-assembly

·

Power management control ECU

·

Junction Connector

·

Wire harness or connector


Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed that is less than 5 km/h (3 mph) for 20 seconds.

*: Only output while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
B2282
·

When the signal from the direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior.

·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the power source mode cannot be turned from on (IG) to off.


-

WIRING DIAGRAM

B318524E04
0.781,1.396 1.906,1.542 1.125,0.146 10 false Skid Control ECU 1.438,0.51 1.729,0.656 0.292,0.146 10 false SP1 0.479,1.396 0.802,1.573 0.323,0.177 10 false A58 1.792,0.51 1.979,0.656 0.188,0.146 10 false 11 3.052,7.448 4.271,7.615 1.219,0.167 10 false Junction Connector 0.563,2.979 1.896,3.354 1.333,0.375 10 false Power Management Control ECU 0.563,2.823 0.854,2.99 0.292,0.167 10 false L5 0.104,7.198 0.365,7.365 0.26,0.167 10 false A48 0.104,7.375 2.417,7.552 2.313,0.177 10 false Headlight Leveling ECU Assembly*4 1.333,6.927 1.75,7.083 0.417,0.156 10 false SPDR 1.385,2.406 1.781,2.563 0.396,0.156 10 false SPDI 1.792,2.406 1.969,2.563 0.177,0.156 10 false 14 1.792,6.917 1.979,7.073 0.188,0.156 10 false 16 3.917,2.427 4.354,2.594 0.438,0.167 10 false 31*2 3.917,2.25 4.354,2.417 0.438,0.167 10 false 32*1 2.875,2.406 3.094,2.573 0.219,0.167 10 false 22 1.792,4.24 1.99,4.406 0.198,0.167 10 false 24 5.292,6.917 5.51,7.083 0.219,0.167 10 false 11 3.917,4.25 4.302,4.417 0.385,0.167 10 false 12*2 4,4.083 4.385,4.25 0.385,0.167 10 false 3*1 2.729,4.25 3.115,4.417 0.385,0.167 10 false 21*2 2.729,4.083 3.115,4.25 0.385,0.167 10 false 12*1 3.917,6.927 4.302,7.094 0.385,0.167 10 false 11*2 3.917,6.75 4.302,6.917 0.385,0.167 10 false 21*1 2.729,6.927 3.115,7.094 0.385,0.167 10 false 32*2 2.729,6.75 3.115,6.917 0.385,0.167 10 false 31*1 5.302,0.51 5.604,0.656 0.302,0.146 10 false 16 5.302,2.406 5.573,2.552 0.271,0.146 10 false 15 5.552,0.625 5.75,0.771 0.198,0.146 10 false SI 5.552,2.51 5.75,2.656 0.198,0.146 10 false +S 4.969,2.771 5.302,2.917 0.333,0.146 10 false L27 4.99,2.927 7.104,3.313 2.115,0.385 10 false Combination Meter Sub-assembly (Meter Circuit Plate) 0.448,4.677 0.813,4.833 0.365,0.156 10 false L146 0.448,4.823 1.979,5.333 1.531,0.51 10 false Windshield Wiper Relay Assembly*3 4.979,6.052 7.115,6.344 2.135,0.292 10 false Navigation ECU Sub-assembly*6 0.208,7.854 1.021,8.031 0.813,0.177 10 false *1: for LHD 1.396,7.854 2.208,8.031 0.813,0.177 10 false *2: for RHD 2.573,7.854 4.344,8.031 1.771,0.177 10 false *3: w/ Auto Wiper System 4.656,7.854 6,8.031 1.344,0.177 10 false *4: w/ LED Headlight 0.208,8.167 1.948,8.344 1.74,0.177 10 false *5: w/o Navigation System 2.573,8.167 4.292,8.344 1.719,0.177 10 false *6: w/ Navigation System 1.448,4.24 1.771,4.385 0.323,0.146 10 false SPD 5.542,6.917 5.865,7.063 0.323,0.146 10 false SPD 4.979,5.906 5.25,6.052 0.271,0.146 10 false L38 4.49,7.25 4.76,7.406 0.271,0.156 10 false L31 4.365,4.542 4.667,4.698 0.302,0.156 10 false L35 4.49,7.396 7.125,7.573 2.635,0.177 10 false Stereo Component Amplifier Assembly*7 4.365,4.698 7.125,4.875 2.76,0.177 10 false Radio and Display Receiver Assembly*5 2.76,7.438 3.073,7.604 0.313,0.167 10 false L70 4.646,8.167 5.844,8.344 1.198,0.177 10 false *7: for 8 Speakers 5.552,4.24 5.865,4.406 0.313,0.167 10 false SPD 5.313,4.24 5.49,4.406 0.177,0.167 10 false 17 5.552,5.583 5.865,5.75 0.313,0.167 10 false SPD 5.313,5.583 5.49,5.75 0.177,0.167 10 false 17 2.99,1.188 4.865,1.333 1.875,0.146 10 false CAN Communication Line 0.208,8.469 2.75,8.646 2.542,0.177 10 false *8: w/ Tire Pressure Warning System

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter sub-assembly. The signal is changed to a pulse signal at the transistor in the combination meter sub-assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in an ECU, all systems in the diagram above will not operate normally.



CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body Electrical / Power Source Control / Trouble Codes.

for Entry&Start: Body Electrical / Entry&Start / Trouble Codes.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2282
Power Source Control
·

Vehicle Speed Signal

·

Power Supply Condition


Combination Meter

Vehicle Speed Meter


-


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

HINT:

If any DTCs for the CAN communication system are output, inspect those DTCs first.


OK:

CAN communication DTC is not output.




OK

2.CHECK SPEEDOMETER OPERATION

NG

2.CHECK SPEEDOMETER OPERATION
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Check the Data List for proper functioning of the vehicle speed signal.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -

OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).




OK

3.READ VALUE USING GTS

NG

GO TO METER / GAUGE SYSTEM (Speedometer Malfunction)

3.READ VALUE USING GTS
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle speed signal Vehicle moving or stationary/Stop or Run Stop: Vehicle stopped
Run: Vehicle moving at 5 km/h (3 mph) or more
-

OK:

Stop (vehicle is stopped) and Run (vehicle is running) appear on the screen.




OK

NG

4.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)
4.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)

OK

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the L27 connector from the combination meter sub-assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-14 (SPDI) - L27-15 (+S) Always Below 1 Ω
L5-14 (SPDI) - Body ground Always 10 kΩ or higher




OK

7.INSPECT COMBINATION METER SUB-ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)
7.INSPECT COMBINATION METER SUB-ASSEMBLY
a.
E343932E03
1.5,0.417 1.917,0.667 0.417,0.25 1.24,1.177 1,0.729 false 0.146,0.104 0.365,0.313 0.219,0.208 10 false *a 0.813,0.573 1.021,0.771 0.208,0.198 10 false S+ 1.042,4.021 1.375,4.25 0.333,0.229 10 false (A) 2.875,3.688 3.219,3.875 0.344,0.188 10 false GND 1.583,0.458 1.927,0.646 0.344,0.188 10 false L27

Remove the combination meter sub-assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

Reconnect the L27 connector to the combination meter sub-assembly.


c.

Reconnect the L5 connector to the power management control ECU.


d.

Connect an oscilloscope to terminal L27-15 (+S) and body ground.


e.

Turn the power switch on (IG).


f.

Turn a wheel slowly.


g.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Driving at approx. 20 km/h (12 mph)

OK:

The waveform is similar to that shown in the illustration.


Text in Illustration
*a Component with harness connected
(Combination Meter Sub-assembly)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




OK

NG

GO TO METER / GAUGE SYSTEM (Speed Signal Circuit)

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the L70 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-15 (+S) - L70-32*1
L27-15 (+S) - L70-31*2
Always Below 1 Ω
L27-15 (+S) - Body ground Always 10 kΩ or higher


*1: for LHD

*2: for RHD




OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - JUNCTION BLOCK)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-14 (SPDI) - L70-22 Always Below 1 Ω
L5-14 (SPDI) - Body ground Always 10 kΩ or higher




OK

REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR